Sewing Knitted Shoulder Seams
A shoulder seam carries the weight of a knit garment, and knit fabric stretches under weight. Without stabilising, the seam grows longer and the garment slips off the shoulder.
Why shoulder seams stretch
The shoulder seam sits where the front and back of a garment meet, and it carries the weight of the sleeves and the body of the garment below it. On a woven garment, the fabric holds its shape and the seam stays the length it was sewn. On a knit garment, the loops of the fabric stretch under that weight, and the seam stretches with them. Each wearing adds a little more length, and the shoulder line slowly drops until the garment fits badly. The fabric itself is not faulty; it is doing what knit fabric does, which is to stretch. The seam needs help to hold its length.
The direction of the stretch matters. A shoulder seam usually runs across the grain where the fabric stretches most, so it takes the full pull of the garment hanging from it. Seams that run with the stretch, such as a side seam, are less affected. That is why the shoulder seam is singled out for stabilising while other seams on the same garment are left to stretch freely.
Ways to stabilise a shoulder seam
Several materials can stabilise a shoulder seam. Clear elastic is a common choice: a narrow strip sewn into the seam adds almost no bulk and holds the length while still allowing a little movement. A woven tape, such as a narrow twill tape, also works, and it gives a firmer result that suits heavier knits and sweaters. A strip of fusible interfacing, cut on the straight grain and fused to the seam allowance, stiffens the seam line and stops it from stretching. A strip of the garment fabric itself, cut on the straight grain so it does not stretch, can be used when no tape is at hand, though it adds a layer of bulk.
The choice depends on the garment. A light jersey top needs only a fine stabiliser, such as clear elastic, so the shoulder stays soft. A heavy hand-knitted sweater needs a firmer tape, since the weight is greater and the loops are larger. A child's garment, which is pulled on and off often, benefits from a stabiliser that can take repeated tugging without breaking.
Cut the stabiliser to the finished length of the shoulder seam, not longer. A stabiliser that is too long lets the seam stretch anyway, and one that is too short pulls the seam in and puckers the shoulder.
Sewing the stabilised seam
- Cut the stabiliser to the length of the shoulder seam and pin it to the seam allowance of the back piece, keeping it flat and unstretched.
- Place the front piece on top, right sides together, and pin through all the layers along the seam line.
- Sew the seam with a stretch stitch or a zigzag, catching the stabiliser in the stitching along the whole length.
- Check the seam by holding it up and letting the garment hang, looking for any sag or stretch along the shoulder line.
- Press the seam allowances toward the back, using a press cloth and lifting the iron rather than pushing it across the knit.
On a hand-knitted sweater, the shoulder seam may be sewn by hand instead of by machine. The same rule applies: a stabilising tape is laid along the seam and caught in the stitches, so the hand sewing holds the length even though the stitches themselves are flexible. A mattress stitch or a backstitch gives a neat join on knitted pieces, and the tape keeps it from growing.
Shoulder seams on sweaters
Sweaters deserve extra care, since they are heavy and their stitches are large. A shoulder seam on a sweater can stretch several centimetres over time if it is not stabilised, which changes the fit of the whole garment. A woven tape sewn into the seam is the usual remedy, and it should be sewn in before the sweater is worn, since a stretched seam is hard to shrink back. Some knitters also sew a short seam across the top of the shoulder, known as a shoulder seam with a slight slope, to match the shape of the body, and the tape follows that slope.
The neckline meets the shoulder seam at one end, and that join needs care too. A neckline that is too loose will pull the shoulder seam outward, so the neckband should be sewn with a slight amount of ease taken in, and the shoulder seam should be checked again after the neckband is attached.
Checking the result
After sewing, hang the garment for a day before judging the shoulder line. Knit fabric settles under its own weight, and a seam that looks right on the table may drop slightly once it has hung. If the shoulder still sags after hanging, the stabiliser may have been too light for the weight, and a firmer tape sewn into the existing seam can correct it. If the shoulder puckers, the stabiliser was probably too short, and easing it out and resewing it to the right length will fix the line.
A stabilised shoulder seam is a small step that protects the whole garment. Done before the first wearing, it keeps the shoulder where it was cut, and the garment keeps its shape for as long as it is worn.