The Seam Line How seams are made, finished, and fixed

Home / Seams on Knits: How They Work

Seams on Knits: How They Work

A knit seam has one job that a woven seam does not: it must stretch. If the seam cannot move with the fabric, the stitches pop the first time the garment is pulled on.

Why knit seams are different

Knit fabric is made of loops, not a woven grid, and those loops can stretch and spring back. That stretch is what makes a knit garment comfortable, and it is also what makes its seams fail. A straight stitch locks the thread in a fixed line, so when the fabric stretches, the thread takes the full pull and snaps. The seam may look perfect on the table and still break the first time the garment is worn. Knit seams must stretch with the fabric, so a straight stitch is usually wrong on knits, and a stretch stitch, a zigzag, or an overlock stitch is used instead.

The stretch in a knit runs in one or both directions, depending on how the fabric was made. Jersey, for example, is a knit fabric with stretch in one or both directions, and the amount of stretch varies from one jersey to another. A seam that runs across the direction of stretch needs to give the most, while a seam that runs with the stretch still needs some give. Testing the fabric by pulling it in both directions shows where the stretch is and how much the seam must allow.

Stitches that stretch

Several stitches suit knits. A narrow zigzag is the most widely available, since almost every home machine can sew one, and it gives the seam room to stretch without breaking. A stretch stitch, sometimes called a lightning stitch, is a narrow zigzag with a slight forward step, and it looks neater than a plain zigzag on the outside. An overlock stitch, sewn on a serger, both joins the seam and finishes the edge in one pass, and it is the stitch used on most ready-made knit garments. A twin needle can also be used for hems, giving two straight lines on the outside and a zigzag underneath that stretches.

Each of these stitches works because the thread has slack built into its shape. When the fabric stretches, the zigzag opens out a little instead of snapping. The width and length of the zigzag set how much give the seam has: a wider, shorter zigzag stretches more, while a narrow, longer one stretches less. A sample in the real fabric shows whether the chosen stitch stretches far enough before it is used on the garment.

Stitch length, tension, and needles

Stitch length on knits is a balance. Stitches that are too long leave the seam loose and wavy, while stitches that are too short can damage the loops of the fabric. A medium length, adjusted after a sample test, is the usual starting point. Tension should be light enough that the seam does not pucker, since puckered knit seams stay puckered after pressing and show on the outside. If the seam ripples, loosening the tension slightly or lengthening the stitch often fixes it.

Needle choice matters more on knits than on wovens. A ballpoint needle pushes the loops of the fabric aside instead of piercing them, which keeps the loops whole and the seam strong. A sharp needle can cut the loops, leaving small holes that run or ladder. A stretch needle, which is a finer ballpoint, suits very stretchy fabrics and helps prevent skipped stitches. A fresh needle is worth fitting before starting a knit project, since a blunt needle damages the loops with every stitch.

Seam types and finishes for knits

The usual seam on a knit garment is a plain seam sewn with a stretch stitch or an overlock stitch, with the allowances pressed to one side or trimmed. An overlocked seam is the most common finish, since it joins and finishes in one pass and the edge stays soft against the skin. A zigzag finish, sewn along the raw edge after the seam is stitched, is the usual choice when no serger is available. Bound and turned finishes are less common on knits, since they add bulk to a fabric that should stay soft and flexible.

Shoulder seams on knits often need stabilising so they do not stretch out. A strip of clear elastic, a narrow tape, or a stay stitched into the seam keeps the shoulder line in place while the rest of the garment keeps its stretch. Without stabilising, a knit shoulder seam can grow longer with wear until the garment slips off the shoulder. The same care applies to any seam that should hold its length, such as a waistband join or a neckline seam.

Seams that should not stretch

Not every seam on a knit garment should stretch. Shoulder seams, waistband joins, and neckline seams hold the shape of the garment, and if they stretch, the garment loses its fit. These seams are stabilised, usually with a strip of clear elastic, a woven tape, or a fusible strip sewn into the seam, so they keep their length while the rest of the garment moves freely. The stabiliser is cut to the finished length of the seam, neither longer nor shorter, so the seam neither grows nor puckers.

The balance between stretchy seams and stable seams is what makes a knit garment fit well. Seams that cross the body, such as side seams and sleeve seams, should give freely. Seams that carry the garment, such as the shoulders, should stay put. Getting that balance right takes a little planning before sewing, and it is the difference between a knit garment that keeps its shape and one that slowly grows out of it.

Pressing and handling knit seams

Knit seams should be pressed gently, with the iron lifted and lowered rather than pushed across the fabric, since pushing can stretch the seam out of shape. A press cloth protects the surface, and steam helps the seam settle without flattening the loops. Pressing the allowances to one side usually suits knits better than pressing them open, since the loops can distort when the seam is opened flat. A sleeve board or a rolled towel supports curved seams while they are pressed, so the shape stays true.

Handling matters during sewing as well. Knit fabric should be fed through the machine without pulling or pushing, letting the feed dogs move it at their own pace. Pulling the fabric as it sews stretches the seam, which then springs back shorter and puckers. A walking foot can help, since it feeds the top and bottom layers together and stops them from shifting.

Knit seams reward a slower pace and a sample test. Sew a short seam, stretch it the way the garment will stretch, and check that the stitches give without popping. When the sample stretches and springs back with the seam still whole, the settings are ready, and the garment will move the way knit fabric is meant to move.