Seam Tools: What Each One Does
Seams are made with a small set of tools, and each one does a job the others cannot. Knowing what each tool is for makes it easier to choose the right one.
The tools that measure and mark
Two small tools handle measuring and marking. A seam gauge is a small ruler, usually with a sliding marker, used for measuring and marking seam allowances, hems, and button spacing. It is short enough to fit in a hand and precise enough to mark a fold at a set distance. A seam allowance ruler is a longer ruler marked with seam allowance widths, used for measuring and marking allowances along a pattern edge or a cut piece of fabric. Both tools do the same kind of work, measuring a distance and marking it, but the gauge suits small, repeated measurements and the ruler suits longer edges.
These tools matter because seam allowance is not a guess. A seam sewn with the wrong allowance changes the fit of the garment, and a hem marked unevenly shows in the finished piece. Measuring with a gauge or a ruler, rather than by eye, keeps the work consistent from one seam to the next.
The tools that guide the stitching
Two presser feet guide the stitching itself. A seam guide presser foot has a guide edge that keeps the stitching a set distance from the edge of the fabric, so the seam allowance stays even along the whole seam. A walking foot feeds the top and bottom layers of fabric together, so they move through the machine at the same speed, which helps on thick or slippery fabric where the layers would otherwise shift. The guide foot is about keeping the seam straight and even. The walking foot is about keeping the layers together.
Both feet fit on an ordinary sewing machine, and both are used in place of the standard presser foot for the seams they suit. The guide foot is useful on long straight seams, where keeping a steady distance from the edge is hard to do by eye. The walking foot is useful on quilts, where three layers must feed evenly, and on fabrics like velvet or leather, where the layers tend to slip.
The tools that take seams apart and finish them
A seam ripper is the tool for removing stitches. It has a sharp forked tip and a small cutting edge for slicing stitches, and it is used to take out seams and to open buttonholes. The safe way to use it is to cut a stitch every few stitches and then pull the thread, not to slide the blade along the seam. It is a small tool, but it is the one that makes sewing forgiving, because a seam can be taken out and sewn again.
Seam finishing scissors, including pinking shears, cut the edge of a seam allowance in a way that slows fraying. Pinking shears cut a zigzag edge, which keeps the threads of the fabric from unravelling as quickly. They are not a substitute for a proper seam finish on fabrics that fray heavily, but they are a quick finish on fabrics that fray little, and they are useful for trimming allowances on curved seams.
The overlocker
An overlocker, also called a serger, is a machine that trims and wraps the edge of a seam in one pass. It cuts the raw edge of the fabric and wraps it in thread at the same time, which gives a clean, professional finish and stops the fabric from fraying. It is used for seam finishing, for sewing knits, and for seams that need to stretch. It does not replace a sewing machine, because it cannot sew a straight seam in the same way, but for finishing edges it is faster and neater than any method a standard machine can offer.
Pressing tools
Pressing has its own tools. A tailor's ham is a curved cushion for pressing curved areas, and a sleeve roll is a narrow cushion for sleeves and narrow seams. A seam roll supports a long seam so it can be pressed without the allowance showing through. A wooden clapper flattens a seam after the iron and holds the heat while the fabric cools. These tools are not needed for a first project, but they make pressing easier and the results more consistent.
Cutting tools for seams
Scissors do the cutting work around a seam. Dressmaking shears cut the fabric, and they are used before the seam is sewn. Seam finishing scissors, including pinking shears, work after the seam is sewn: they trim the edge of the seam allowance, slow fraying, and reduce bulk. Small embroidery scissors snip thread ends close to the fabric without nicking it. A seam ripper belongs in this group too, though it cuts thread rather than fabric, and it is the tool that undoes a seam when it needs to be sewn again. Each of these is a cutting tool, but each cuts a different thing, and using the right one for the job keeps both the fabric and the tool in good condition.
Keeping cutting tools sharp matters more than it seems. A dull blade drags the fabric instead of cutting it, and a dragged cut is uneven and can distort the edge. Scissors used on paper dull quickly, so they should be kept for fabric only, and a seam ripper used on anything but thread dulls the same way. Sharp tools need less force, and less force means more control.
Starting with the essentials
A beginner does not need every tool at once. A seam ripper, a seam gauge, and a presser foot with a guide edge cover the most common needs: taking out a mistake, measuring an allowance, and keeping a seam straight. The other tools can be added as the work calls for them: a walking foot when slippery fabric appears, an overlocker when seam finishing becomes a regular job, and a ham and roll when curved seams and sleeves become common. Each tool earns its place by solving a problem that the existing tools cannot. It is better to add one tool at a time, and to learn it properly, than to buy a full set and use none of them well. A small set of tools that are understood beats a large set that is not.
Storing the tools well keeps them in good condition. Measuring tools should be kept flat, so they do not warp, and presser feet should be kept in a small box or pouch, so they do not knock against each other and get damaged. Scissors should be stored closed, with the blades protected, and the seam ripper should be kept capped. A tool that is stored properly lasts longer and works better, and it is also easier to find: a sewing box where each tool has a place is a box where the right tool is always to hand when it is needed.
The tools are simple, and that is their strength. Each one does one job well, and together they cover the whole life of a seam, from measuring it to pressing it flat.