Seam Allowance Ruler
A seam allowance ruler is a ruler marked for the distances sewing uses most, so an allowance can be measured and marked along a long edge without stopping to work out the numbers.
What it is
A seam allowance ruler is a straight ruler, usually longer than a seam gauge, with markings that show seam allowance widths directly. Instead of measuring in centimetres and then adding an allowance, the ruler is laid along the edge of a pattern or a piece of fabric, and the allowance line can be read or marked straight from its edge. Some allowance rulers are transparent, so the fabric or pattern underneath can be seen through them, and some have a sliding marker like a seam gauge. The length varies, but a ruler of thirty centimetres or more suits the long edges of pattern pieces.
The ruler is a measuring and marking tool. It does not cut fabric, and it is not a substitute for a pattern. Its job is to make the step between a pattern edge and a cutting line quick and accurate, so the allowance added is the same width along the whole edge.
Measuring an allowance
To measure an allowance, lay the ruler along the edge of the pattern piece or the fabric, with the zero mark at the edge and the ruler extending into the piece. The allowance width the pattern calls for is read from the markings, and the stitching line or the cutting line can be marked with chalk or a fabric marker. On a long edge, the ruler is moved along in sections, marking as it goes, so the line stays straight. The transparency of many allowance rulers helps here, because the pattern line underneath stays visible while the ruler is in place.
The ruler is also used to check an allowance that has already been added. Laying it across the allowance shows whether it is the width it should be, and whether it stays the same along the edge. An allowance that varies in width will change the fit of the garment, and it is easier to catch with a ruler than by eye.
Marking a cutting line
When a pattern has no allowance printed on it, the allowance must be added before the fabric is cut. The ruler is laid along the pattern edge, the allowance width is marked at intervals, and the marks are joined to form the cutting line. This is the step where the ruler earns its keep: marking a long edge by measuring each point with a short gauge would take much longer, and the line would be less even. The ruler covers the length in fewer moves, and the marks line up more cleanly.
On a curved edge, the ruler cannot follow the curve, so the allowance is marked at short intervals and the marks are joined freehand, or the pattern is traced with the allowance added by eye at each point. The ruler still helps, because each mark is measured accurately, even if the line between them is drawn by hand.
Checking a pattern
Patterns do not always print the allowance width on the piece, and a pattern that has been traced or altered may have lost its markings. The allowance ruler checks what is there: lay it across the allowance on the pattern and read the width. If the allowance is not the width the instructions call for, the pattern needs to be corrected before the fabric is cut. It is a small check, and it prevents the larger problem of a garment that does not fit because the allowances were wrong from the start.
The ruler is also useful for checking the seam allowance on a finished seam, or for measuring the distance from a seam to a topstitching line. Any distance that is an allowance width, or a multiple of one, can be checked with it. When a pattern has been altered, for example by adding width at a side seam, the ruler checks that the allowance on the altered edge is still the width it should be, since an altered edge can lose its allowance if the change is drawn carelessly.
Choosing and caring for one
An allowance ruler should be straight, with markings that are easy to read and that do not wear off with use. A transparent ruler is easier to use on patterned fabric, because the fabric can be seen through it. A metal ruler lasts longer than a plastic one, but it is heavier and it can be cold to handle. The length should suit the work: a short ruler for small pieces, a long one for pattern edges and garment lengths.
Keep the ruler flat and out of heat, which can warp plastic. Check its markings against another ruler now and then, since a ruler that has been worn or damaged can give a wrong measurement. A ruler is only useful if it is accurate, and accuracy is worth checking. It is also worth keeping the ruler with the pattern work rather than in a general toolbox, since a ruler that is always where the patterns are gets used, and one that has to be fetched from another room gets skipped in favour of guessing.
When a pattern is traced onto paper or fabric, the ruler adds the allowance to the traced line. Lay the ruler along the traced edge, mark the allowance width at intervals, and join the marks to form the cutting line. This is the step where a long ruler is much faster than a short gauge, since a traced pattern edge can be long and the ruler covers it in fewer moves. The marks line up cleanly, the cutting line is straight, and the allowance is the same width along the whole edge, which is what the traced pattern needs.
A seam allowance ruler is a simple tool, but it makes the measuring that sewing depends on faster and more reliable. The allowance is the same width along the whole edge, the cutting line is straight, and the garment fits as the pattern intended.