The Seam Line How seams are made, finished, and fixed

Home / Standard Seam Allowances

Standard Seam Allowances

Most patterns use one of a small set of allowance widths. Knowing the set makes it easy to spot when a pattern departs from it, and why.

The garment standard: 5/8 inch

Common pattern allowances are 5/8 inch (1.5 cm) for garments and 1/4 inch for quilting, but allowances vary, so the pattern should always be checked before cutting. The 5/8 inch garment allowance is the long standing standard in commercial patterns. It leaves enough fabric for the stitches to grip, for the seam to be pressed open neatly, and for a fitting change later, such as letting a side seam out by a small amount.

That width suits medium weight woven fabrics, which are the fabrics most garment patterns are drafted for. It is wide enough to finish the raw edge by overlocking or zigzag stitching without catching the stitches, and narrow enough that the bulk inside the garment stays manageable. When a pattern gives no other information, 5/8 inch is the width a maker expects to find.

Metric patterns often state the same allowance as 1.5 cm, which is very close to 5/8 inch. The small difference between the two does not matter in practice, but mixing them on one project does. Choose one system for the whole project and keep it.

The quilting standard: 1/4 inch

Quilting uses a 1/4 inch allowance, about 6 mm. Quilt blocks are pieced from many small shapes, and the finished size of a block depends on every seam being exactly 1/4 inch. A wider allowance would add bulk at every join and distort the block. A narrower one would leave too little fabric for the stitches to hold through quilting and washing.

Quilters measure this allowance with care. A 1/4 inch presser foot, a marked throat plate, or a seam guide is used to hold the distance, and the first seam is checked against a ruler. A difference of even a thread or two, repeated across a dozen seams in a block, changes the block size enough to notice when blocks are joined into rows.

Quilt seams are usually pressed to one side rather than open, so that the allowances in one row nest against the allowances in the next. That nesting only works when every allowance is the same width, which is another reason the 1/4 inch standard is held so strictly.

Other widths and where they appear

A 1/2 inch allowance appears on many simple patterns, on children's clothing, and on items sewn from rectangles. It is a practical middle width: easier to handle than 1/4 inch, less bulky than 5/8 inch, and simple to mark on a ruler.

A 3/8 inch allowance appears on small items, on curved edges, and on patterns drafted for lightweight fabrics. It reduces bulk where a wider allowance would show through or resist turning. A 1/4 inch allowance also appears on garments in some places, such as a neckline or an armhole that will be faced or bound, where the raw edge ends up enclosed and a wide allowance would add unwanted layers.

A 1 inch allowance appears where change is expected. A centre back seam or a side seam may carry 1 inch so the garment can be let out. Hem allowances are usually 1 inch or wider, and sometimes 2 inches on a coat or a long skirt, because a hem needs fabric to turn up, hold its shape, and sit flat.

Allowances by seam type

Different seam types call for different allowances. A plain superimposed seam, where two layers are placed face to face and stitched, uses the pattern allowance as stated, usually 5/8 inch on garments. A French seam uses a two stage allowance: a narrow first stitch, often 1/4 inch, then a second stitch that encloses the raw edges, so the total allowance ends up near the standard width.

A flat-felled seam, the strong seam used on jeans and shirts, needs a wider allowance, because one side is folded over the other and stitched down. A lapped seam, where one edge overlaps the other, needs allowance on the overlapping piece and a finished edge on the under piece. A bound seam needs enough width for the binding to wrap the raw edges.

When a pattern calls for a special seam, the instructions usually state the allowance for that seam separately. If they do not, the seam type guide for that seam is the place to check before cutting.

Allowances by fabric

Fabric weight and behaviour change the sensible width. Heavy fabrics such as denim and coating need a narrower allowance on curved seams, because wide allowances in heavy fabric create stiff ridges. The same fabrics may keep a standard allowance on straight seams, where the bulk can be pressed flat or graded.

Lightweight and sheer fabrics often use a narrow allowance, since a wide one would show through the fabric as a shadow. Fabrics that fray easily, such as loosely woven linen or some rayons, benefit from a wider allowance, because the stitches need more fabric to grip and the raw edge needs room for a finish.

Stretch fabrics follow the pattern allowance like any other fabric, but the stitch type changes. A stretch stitch or a narrow zigzag is used so the seam can stretch with the fabric. The allowance width itself stays as the pattern states it.

Metric and imperial side by side

Patterns come in both systems, and the common equivalents are worth knowing. A 1/4 inch allowance is about 6 mm. A 3/8 inch allowance is about 1 cm. A 1/2 inch allowance is about 1.3 cm. A 5/8 inch allowance is 1.5 cm. A 1 inch allowance is 2.5 cm.

The conversions are approximate, and that is fine. What matters is consistency within a project. If the pattern is metric, use the metric numbers. If it is imperial, use the imperial numbers. Switching systems halfway through a project introduces small differences that add up across seams.

When in doubt, the pattern instructions settle the question. The stated allowance is the standard for that pattern, even when it differs from the widths listed here. Standards describe what is usual, and the pattern describes what this project needs. Check the pattern first, and treat the list above as the background that makes the pattern number easy to read.