Seam Allowance Adjustments for Patterns
When a pattern piece changes shape, its seam allowance has to change with it. An allowance left behind is how adjusted pieces stop fitting together.
Why adjustment touches the allowance
Seam allowance is the fabric between the stitching line and the raw edge, and it is drawn relative to the stitching line. When a pattern is adjusted, the stitching line moves, so the cutting line has to move by the same amount to keep the allowance even. If the stitching line moves out by 1/2 inch and the cutting line stays where it was, the allowance on that edge shrinks by 1/2 inch. If the allowance was 5/8 inch, it becomes 1/8 inch, which is too narrow to hold a seam well.
The reverse is also true. Moving the stitching line inward without moving the cutting line widens the allowance, which adds bulk and changes how the seam presses. Either error is easy to make when an adjustment is drawn on the tissue in a hurry, and both show up later as seams that do not match or allowances that will not press flat.
The rule is simple to state and worth repeating: redraw the allowance whenever the stitching line moves. The allowance is not a fixed border around the piece. It is a fixed distance from the stitching line, and it follows that line wherever it goes.
Widening or narrowing a piece
Adding width to a piece is the most common adjustment. A bodice may be widened at the side seam, a skirt at the hip, or a sleeve at the bicep. The usual method is to draw the new stitching line at the new position, then draw the new cutting line outside it at the allowance distance.
On a straight edge, that is a matter of measuring out the allowance with a ruler and drawing a parallel line. On a curved edge, the new cutting line must follow the new curve at an even distance. A common mistake is to draw the new cutting line as a straight line across a curve, which makes the allowance wide in one place and narrow in another. Short marks at regular intervals along the curve, joined into a smooth line, give a better result.
When width is added at a seam shared by two pieces, both pieces need the same treatment. If a bodice front is widened at the side seam by 1/2 inch, the bodice back is usually widened by the same amount at its side seam, so the two stitching lines stay the same length and the pieces still join.
Lengthening or shortening
Length changes are usually made at marked lengthen and shorten lines printed on the pattern, which sit between the seams rather than at them. Cutting the tissue at that line, spreading or overlapping the pieces, and taping them flat changes the length without touching the allowance at the top or bottom edges.
When a length change is made at an edge instead, the allowance has to be considered. Shortening a sleeve by cutting off the bottom, for example, removes the hem allowance as well as the length. The hem allowance must be added back below the new hem line, or the sleeve will finish without enough fabric to turn up. The same applies to shortening a skirt or a trouser leg at the hem.
Lengthening at an edge needs the opposite care. Adding length at the hem means adding the length plus the hem allowance, so the finished hem still has its full turn-up. Adding length at a shoulder or a waist seam means the adjoining piece may need the same addition, or the seam lengths will no longer match.
Changing the allowance itself
Sometimes the adjustment is to the allowance, not to the size. A maker may want a wider allowance on a side seam to allow future letting out, or a narrower allowance on a neckline that will be faced. The change is made by redrawing the cutting line while leaving the stitching line in place.
To widen an allowance from 5/8 inch to 1 inch, draw a new cutting line 3/8 inch outside the old one. The stitching line does not move, so the finished size does not change. To narrow an allowance from 5/8 inch to 1/4 inch, draw the new cutting line 3/8 inch inside the old one, again leaving the stitching line alone.
Changing the allowance on one edge of a seam without changing the other side is fine, since the two allowances do not have to match each other. What must match is the stitching line length on both pieces. As long as the stitching lines stay the same length, the pieces will join, even if one side carries a wider allowance than the other.
Adjusting for a different seam type
Changing the seam type changes the allowance needed. Replacing a plain superimposed seam with a French seam keeps the total allowance the same but splits it into two passes, so the cutting line stays put and only the stitching plan changes. Replacing a plain seam with a flat-felled seam needs a wider allowance, because one side folds over the other, so the cutting line on the folding side moves outward.
A lapped seam needs allowance on the overlapping piece and a finished edge on the piece underneath. If a pattern drafted for a plain seam is sewn as a lapped seam, the under piece needs its allowance trimmed back and its edge finished, or the overlap will sit unevenly.
These changes are best drawn on the pattern before cutting, not improvised at the machine. A drawn cutting line is easy to check against the adjoining piece. An allowance trimmed at the machine, by eye, is hard to keep even along a long seam.
A short checklist before cutting adjusted pieces
Before cutting, walk through the adjusted pieces with a ruler. Check that every stitching line that joins another piece is the same length as its partner. Check that every cutting line sits at the stated allowance distance from its stitching line, following curves evenly. Check that notches and matching points still sit in the right places relative to the new stitching lines.
Then check the hem and facing allowances separately, since those are the ones most often lost in a length change. A piece that is right everywhere except the hem will still sew up wrong, and the error will only show at the end of the project.
Pattern adjustment is a normal part of sewing, not an advanced skill reserved for later. The allowance is the part that makes it work or fail, and redrawing it with the stitching line is the single habit that keeps adjusted pieces fitting together. Draw the new stitching line, draw the cutting line at the right distance from it, and check the joins before cutting.