Seam Allowance and Fit
Fit is often adjusted at the seams, and the seam allowance is what makes that possible. It is the spare fabric that lets a seam move.
How allowance relates to size
Seam allowance is the fabric between the stitching line and the raw edge. The finished size of a garment is set by where the stitching lines sit, not by where the fabric was cut. Moving a stitching line changes the size of the piece it belongs to, and the allowance is the fabric that allows that move.
Stitching further from the raw edge, which means a narrower allowance, makes the piece larger. Stitching closer to the raw edge, which means a wider allowance, makes the piece smaller. On a bodice with four vertical seams, moving each stitching line by 1/8 inch changes the circumference by a full inch, because each seam is counted twice, once on each side of the body.
That arithmetic is why fitting changes are usually made in small steps. A 1/4 inch change at a single seam is a large fitting change. A 1/8 inch change at two seams is often enough to fix a garment that feels slightly tight or slightly loose.
Taking a seam in
Taking a seam in means stitching a new line further from the raw edge than the original, which makes the garment smaller at that seam. The old stitching is usually removed first, or the new line is stitched and the old stitches are removed after, so the fabric can lie flat at the new line.
The limit is the fabric available. Taking a seam in uses up allowance, and the new seam needs enough allowance left to hold and to press. A seam that started with a 5/8 inch allowance and is taken in by 1/4 inch still has 3/8 inch left, which is workable. Taking the same seam in by 1/2 inch leaves only 1/8 inch, which is too narrow to finish safely.
When a garment needs taking in by more than the allowance allows, the change has to come from elsewhere. A dart can be deepened, a new dart can be added, or a panel can be recut. The allowance sets the limit for seam based fitting, and recognising that limit saves time spent forcing a seam further than it can go.
Letting a seam out
Letting a seam out is the reverse: stitching a new line closer to the raw edge, which makes the garment larger at that seam. This is only possible when the allowance is wide enough. A garment sewn with a 5/8 inch allowance can usually be let out by about 1/4 inch at a seam and still leave enough fabric for the stitches to hold. Letting it out further risks a seam that pulls apart, because the stitches sit too close to the raw edge and the fabric frays past them.
Old stitch holes are a practical problem when letting out. The needle holes from the first stitching line stay visible on some fabrics, especially smooth or tightly woven ones, and they sit inside the garment after letting out. Pressing with steam sometimes helps them close, and on other fabrics they remain. This is one reason fitting is best done with a toile or a muslin before cutting good fabric, rather than by letting out a finished garment.
Side seams and centre back seams are the usual places to let a garment out, because they run the length of the body and the change is spread evenly. A centre back seam often carries a wider allowance than other seams for exactly this reason, sometimes 1 inch, so there is room to adjust.
Where fit changes are made
Not every seam is a good place for a fitting change. Side seams and centre seams adjust circumference. Shoulder seams adjust length and slope. A princess seam, which runs from the shoulder or armhole over the bust and down the front, adjusts shape through the bust and waist in a smooth curve, and it is often the best place for a fitted change on a bodice.
Waist seams adjust length above and below the waist. Sleeve seams adjust the circumference of the arm. Changing a seam that runs across the grain, such as a waist seam, affects how the garment hangs, so those changes are usually kept small and checked on the body.
When several seams need changing, it helps to change them by the same small amount rather than making one large change at a single seam. A garment taken in by 1/2 inch at one side seam will pull and twist. The same total taken in by 1/8 inch at four seams keeps the balance of the garment.
Fitting with a toile
A toile is a test garment sewn in inexpensive fabric, usually calico or muslin, to check fit before cutting the real fabric. It is the most reliable way to find out how much a seam needs to move, because the changes can be pinned, tried on, and adjusted without risking good fabric.
On a toile, fitting changes are marked with pins or pen directly on the seams. The marked line becomes the new stitching line, and the allowance beyond it is checked to make sure enough remains. The toile is then taken apart and used as the pattern for cutting, or the changes are transferred back to the paper pattern.
Even without a full toile, a fitting check on the real garment before finishing helps. Trying a garment on with the seams basted, meaning temporarily stitched with long loose stitches, lets the fit be checked and changed while the allowance is still full and the seams are easy to open.
Fit changes should be tried on the body, not only measured flat. A garment that measures right on the table can still pull when worn, and a pinned fitting shows that before the final stitching goes in.
Allowance and fit belong together. The allowance is the margin that lets a seam move, and the stitching line is the control that sets the size. Small moves, spread across several seams, checked on the body before final stitching, give a better result than one large move made in a hurry. Keep the allowance wide enough to allow a change, and the fit will stay adjustable until the garment is finished.