How to Sew Seams on Knits
Knit seams are sewn differently from woven seams, but the steps are simple once the machine is set up for stretch. The fabric does most of the work if it is allowed to move naturally.
Setting up the machine
Start by fitting a ballpoint needle, which pushes the loops of the knit aside instead of piercing them. A sharp needle can cut the loops and leave holes that run, so the ballpoint is the safer choice for any knit. Choose a thread that has some give, since a thread with no stretch will snap even if the stitch shape is right. Polyester thread is a common choice for knit seams because it stretches a little and resists wear.
Set the machine to a stretch stitch or a narrow zigzag. The zigzag width sets how much the seam can stretch: a width that is too narrow gives little, while a width that is too wide can look untidy on the outside. A stitch length in the middle range is the usual starting point. Loosen the tension slightly if the sample puckers, and test the settings on a scrap of the same fabric before sewing the garment. The sample should stretch without the stitches popping and spring back without rippling.
Preparing the fabric
Cut knit fabric with the stretch running the right way for the garment, and mark the pieces clearly so they are not turned the wrong way during sewing. Pin within the seam allowance, using pins placed across the seam line so they do not distort the fabric, and use plenty of them, since knit layers shift easily. Clips can be used instead of pins on fabrics that mark easily. If the fabric curls at the edges, flatten it gently and let it settle before pinning, rather than pulling it straight, which stretches the edge out of shape.
Shoulder seams and any seam that should hold its length need stabilising. A strip of clear elastic or a narrow stabilising tape, basted or pinned into the seam, stops the seam from stretching out during wear. This step is easy to skip and hard to fix later, so it is worth doing while the pieces are still flat.
Sewing the seam
- Place the pieces right sides together and pin or clip along the seam line, keeping the edges even without stretching them.
- Sew the seam with the chosen stretch stitch or zigzag, guiding the fabric gently and letting the feed dogs move it.
- Do not pull the fabric from behind or push it from the front, since either one stretches the seam out of shape.
- Backstitch a few stitches at the start and end to secure the seam, or leave long thread tails to tie off if backstitching distorts the fabric.
- Check the seam by stretching it gently across the stitching, the way the garment will stretch in wear.
- Press the seam allowances to one side, using a press cloth and lifting the iron rather than pushing it.
If the seam ripples, the fabric was probably pulled during sewing or the tension was too tight. Unpick the worst of it, loosen the tension slightly, and sew again without pulling. A walking foot can help on knits that feed unevenly, since it moves the top layer at the same pace as the bottom one.
Sewing curves and corners on knits
Curved seams on knits, such as an armhole or a neckline, need a slower pace and shorter stretches of sewing between pins. Pin generously around the curve, placing the pins close together so the layers cannot shift, and sew slowly, stopping with the needle down to turn the fabric a little at a time. Pulling the fabric around a curve stretches it, and a stretched curve will not lie flat once it is sewn. A stay stitch, a line of straight stitching just inside the seam line, can hold a curved edge steady while the seam is sewn, and it is worth adding on necklines and armholes that tend to grow.
Corners on knit garments are usually clipped or trimmed after sewing, so the allowance can turn cleanly. Trim the bulk from the corner, turn it through, and press it gently with a point presser or a rolled towel. A corner that is left bulky will pull the seam out of shape and show as a lump on the outside.
Finishing the edges
Knit edges fray less than woven edges, but they still need a finish to stay tidy. An overlock stitch finishes the edge and joins the seam in one pass when a serger is available. Without a serger, a zigzag stitched along the raw edge after the seam is sewn keeps the edge from curling and fraying. Trimming the allowance close to the stitching is another option on stable knits, though it leaves the edge bare and suits only fabrics that do not fray at all.
The finish should stay soft. A stiff or bulky finish on a knit seam defeats the purpose of the fabric, which is meant to move and drape. Keep the finish light, and the seam will feel as good as it looks.
Common problems and fixes
Skipped stitches on knits usually mean the needle is wrong for the fabric. A stretch needle, which is a finer ballpoint, often fixes skipping on very stretchy fabric. Puckering usually means the tension is too tight or the fabric was pulled during sewing. A seam that pops when stretched means the stitch did not give enough, and a wider zigzag or a stretch stitch is the fix. Wavy seams usually mean the fabric was stretched while it was sewn, and the remedy is to sew again with a lighter touch and a walking foot if one is available.
Each of these problems is fixed at the machine, not after the garment is finished. A short sample before the real sewing catches most of them, and a sample after any change confirms the fix. Sew the sample, stretch it, press it, and only then sew the garment.