The Seam Line How seams are made, finished, and fixed

Home / Seam Finishes for Knits

Seam Finishes for Knits

A seam finish on a knit should do its job without making the seam stiff. The best finishes protect the edge and let the seam stretch, all in a soft layer that sits flat against the skin.

What a finish does on a knit

A seam finish protects the raw edge of the seam allowance. On a woven fabric, the edge frays if it is left bare, and the finish stops the threads from unravelling. On a knit, the loops fray less, but the edge can still curl, roll, and look untidy, and on some knits the cut loops do work loose over time. A finish keeps the edge tidy through wearing and washing, and it stops the allowance from curling into the seam line, where it would show as a ridge on the outside.

The finish also affects comfort. A knit garment sits close to the skin, so a stiff or bulky finish can rub and irritate. A soft finish, such as an overlocked edge or a light zigzag, stays comfortable and does not add a ridge. The finish should be chosen with comfort in mind, not just with neatness.

Overlocked finish

An overlocked finish is the most common finish on knit garments. The serger wraps thread around the raw edge, joining the seam and finishing it in one pass, and the result is a soft, stretchy edge that lies flat. The overlock stitch gives with the fabric, so the seam stretches without popping, and the wrapped edge does not fray or curl. On a garment sewn with a serger, the overlocked finish is the natural choice, and it needs no second step.

The width of the overlock can be adjusted to suit the fabric. A wider overlock covers more of the edge and suits fabrics that fray or curl, while a narrower one is lighter and suits fine knits. The thread should match the fabric in weight, so the edge stays soft rather than stiff.

Zigzag and stitched finishes

Without a serger, a zigzag stitched along the raw edge is the usual finish. It is sewn after the seam itself, close to the edge, and it stops the edge from curling and fraying. The zigzag should be narrow and fairly dense, so it grips the edge without adding bulk. A second option is to stitch the seam with a stretch stitch and then trim the allowance close to the stitching, which suits stable knits that do not fray at all. The trimmed edge is the lightest finish of all, though it leaves the edge bare and is best kept for fabrics that have been tested and shown not to unravel.

A bound finish, where a strip of fabric is folded over the edge and stitched down, is rarely used on knits, since it adds two layers of bulk to a seam that should stay soft. A turned and stitched finish, where the edge is folded under and stitched, can work on a stable knit, but it stiffens the seam and is better kept for hems than for seams.

Choosing a finish by fabric

Fine jersey takes a light finish: a narrow overlock or a fine zigzag, with no trimming that would weaken the edge. Medium knits, such as cotton jersey and interlock, take a standard overlocked or zigzag finish, and the allowance can be trimmed after the finish is sewn. Heavy knits and sweater knits often need no finish at all beyond the seam itself, since the loops are large and the edge does not fray, though a loose zigzag can tidy a curling edge.

Very stretchy fabrics, such as swimwear knits, need a finish that stretches as far as the fabric does. A wide zigzag or a three-thread overlock gives the most, while a narrow finish can snap when the garment is pulled on. A sample that is stretched hard after finishing shows whether the finish keeps up with the fabric.

Finish a sample before finishing the garment. Stretch the finished sample the way the garment will stretch in wear, and check that the finish gives without popping or pulling the seam out of shape.

Finishes for hems and necklines

Hems and necklines on knits need finishes that stretch, just as the seams do. A hem finished with a straight stitch will snap when the edge is pulled, so a twin needle hem is the usual choice without a serger: two straight lines show on the outside, with a zigzag underneath that gives when the fabric stretches. A neckline is often finished with a band, a strip of the same knit folded over the edge and stitched with a stretch stitch, which holds the curve in shape and gives a clean edge that can be pulled on without popping.

Binding a knit edge with a woven binding is a poor match, since the binding does not stretch and the knit does, so the edge puckers and the binding pulls away. A knit binding, cut from the same fabric or a matching knit, moves with the garment and stays smooth. The same rule holds for any edge finish on a knit: the finish must stretch as far as the fabric it edges, or it will fail first.

Pressing a finished knit seam

Press a finished knit seam gently, with the iron lifted and lowered rather than pushed across the fabric. Pushing can stretch the seam and distort the finish. A press cloth protects the surface, and steam helps the seam settle without flattening the loops. Pressing the allowances to one side usually suits knits better than pressing them open, since opening a knit seam can distort the loops along the stitching line.

A finish that is chosen for the fabric, sewn with a stitch that stretches, and pressed lightly will last as long as the garment. It stays soft, it stays flat, and it keeps the seam edge tidy through every wash.