Seams on Jersey
Jersey is the knit most people meet first: soft, stretchy, and used for T-shirts, dresses, and children's clothes. Its seams need the same care as any knit seam, with a few habits that suit jersey in particular.
What jersey is
Jersey is a knit fabric with stretch in one or both directions, made in a single-knit structure that gives it a smooth face and a slightly different back. It is usually made from cotton, or from cotton mixed with a stretch fibre, and it drapes softly, which is why it suits T-shirts, dresses, tops, and children's clothes. The stretch is usually greater across the width than along the length, though some jerseys stretch both ways, and the amount varies from one jersey to another. Pulling a scrap in both directions before cutting shows where the stretch is and how much the seams must allow.
Jersey has habits that affect sewing. Its cut edges curl toward the face, which makes pinning and feeding trickier than on a stable woven fabric. It can also grow as it is handled, so a piece measured flat may end up longer after it has been moved around the table. Letting the fabric rest flat before cutting, and handling it gently, keeps the pieces true to the pattern.
Stitches for jersey seams
Jersey seams need a stitch that stretches. A narrow zigzag is the most widely available choice, and it suits most jersey weights. A stretch stitch looks neater and lies flatter, and it is a good choice where the seam will show, such as on a neckline or a hem. An overlock stitch joins and finishes the seam in one pass on a serger, and it is the stitch used on most ready-made jersey garments. A straight stitch is usually wrong on jersey: it cannot stretch, so it snaps when the garment is pulled on, however neatly it was sewn.
The stitch settings should be tested on a scrap of the same jersey. Stretch the sample across the stitching and check that the stitches give without popping. If they pop, widen the zigzag or shorten the stitch length slightly. If the seam puckers, loosen the tension or lengthen the stitch. Jersey varies enough that a setting that worked on one jersey may need adjusting on the next.
Needles and thread for jersey
A ballpoint needle is the right needle for jersey, since it pushes the loops of the knit aside instead of piercing them. A sharp needle can cut the loops and leave small holes that run or ladder, which shows as a line of tiny holes along the seam. A stretch needle, which is a finer ballpoint, helps prevent skipped stitches on jersey with a high stretch content. A fresh needle is worth fitting at the start of a jersey project, since a blunt needle damages the loops with every stitch.
Thread with some give suits jersey, and polyester thread is a common choice because it stretches a little and resists wear. The thread weight should match the jersey: a fine thread for a light jersey, and a medium thread for a heavier one. A thread much heavier than the fabric needs can leave large needle holes and a stiff seam.
Handling jersey while sewing
- Let the fabric rest flat before cutting, so it stops growing and the pieces stay true to size.
- Pin or clip the pieces right sides together, placing pins across the seam line so the curling edges stay flat.
- Sew with a stretch stitch or a narrow zigzag, guiding the fabric gently and letting the feed dogs move it.
- Do not pull the fabric from behind or push it from the front, since either stretches the seam out of shape.
- Stabilise the shoulder seams with a strip of clear elastic or tape, so they do not stretch out under the weight of the garment.
- Press the seam allowances to one side with a press cloth, lifting the iron rather than pushing it across the jersey.
A walking foot helps on jersey, since it feeds the top and bottom layers together and stops them from shifting. Without one, the top layer can lag and the seam can end up with one side longer than the other. Slowing down helps too: jersey sewn slowly stays even, while jersey sewn fast tends to ripple.
Necklines, hems, and finishing
Necklines on jersey need a stay or a stabiliser, since the edge is cut on a curve and stretches easily. A strip of fusible tape or clear elastic sewn into the neckline seam keeps it from growing, and the neckband should be cut slightly shorter than the neckline so it pulls the edge in gently. Hems on jersey are often sewn with a twin needle, which gives two straight lines on the outside and a zigzag underneath that stretches, or with a coverstitch on a serger where one is available.
The raw edges of jersey seams are usually finished with an overlock stitch or a zigzag along the edge. Jersey frays little, so a light finish is enough, and the aim is to stop the edge from curling rather than to stop heavy fraying. A finish that is too stiff defeats the softness of the fabric, so keep it light and let the jersey drape the way it was made to.
Jersey rewards gentle handling and a tested stitch. Sew a sample, stretch it, press it, and check that the seam moves with the fabric. When the sample passes, the garment will too, and the jersey will keep the soft, easy fit that makes it so widely worn.