Seams on Sweaters
Sweater seams join pieces that are thick, heavy, and stretchy. They need a flexible join that holds the shape of the garment without making a stiff ridge.
How sweater seams differ
A sweater is usually knitted in pieces, a front, a back, and two sleeves, and the seams join those pieces into a garment. The knitting is thicker than jersey and the loops are larger, so the seam has to cope with bulk as well as stretch. A seam that is too tight will pucker the knitting and show as a ridge. A seam that is too loose will gap and let the pieces shift. The join should be firm enough to hold the shape and flexible enough to move with the wearer.
Weight is the other difference. A sweater is heavy, and its weight pulls on the shoulder and side seams whenever it is worn. Seams that would hold on a light knit top can stretch out on a sweater, especially at the shoulders. That weight is why sweater seams are often sewn with a stabiliser at the shoulder and checked by hanging the garment before the fit is judged.
Joining knitted pieces
Knitted pieces are usually joined by hand, using a yarn needle and the same yarn as the knitting, or a matching thread. A mattress stitch is the most common method: it works through the edge stitches of each piece and pulls them together into a nearly invisible join, with the seam allowances folding neatly to the inside. A backstitch gives a firmer join and suits seams that carry weight, though it can show more on the outside. A whip stitch is quicker but less neat, and it suits seams that will be hidden inside the garment.
Machine sewing is also possible on finer sweater knits, using a stretch stitch or a zigzag and a ballpoint needle. The pieces are pinned right sides together and sewn along the seam line, the same way as any knit seam. Machine sewing is faster, but it can flatten the loops near the seam, so it suits finer knits better than chunky ones. Whichever method is used, the pieces should be blocked, that is, shaped and left to dry flat, before they are joined, so the edges match in length.
Side seams and sleeve seams
Side seams on a sweater run from the hem to the underarm, and they set the width of the body. They should be sewn with the pieces lying flat and the edges matched stitch for stitch, so the seam does not pull the body out of shape. If one piece is slightly longer than the other, ease it in evenly along the seam rather than gathering it at one end. Sleeve seams run from the cuff to the underarm and need the same care, since a sleeve that twists will not hang straight.
Setting a sleeve into a sweater is the most demanding seam on the garment. The sleeve cap is eased into the armhole, with more fullness at the top and less at the sides, and the seam is sewn in stages, checking the fit as it goes. Pinning generously and sewing slowly keeps the easing even. A sleeve that is set in well moves freely and shows no puckers at the cap.
Shoulders and necklines
Shoulder seams on sweaters must be stabilised, since the weight of the garment pulls on them constantly. A woven tape sewn into the seam holds the length, and the tape should be cut to the finished shoulder length so it neither stretches nor puckers. The neckline meets the shoulder at one end, and a neckband that is too loose will pull the shoulder seam outward, so the band should be eased in slightly when it is attached.
Neckline seams need a neat finish, since they are visible when the sweater is worn. A ribbed band, picked up and knitted from the neckline edge, gives a clean edge that stretches when the sweater is pulled on. A band that is too tight will pucker the neckline, and one that is too loose will gape, so the number of stitches picked up should be checked against the pattern and adjusted if the knitting is looser or tighter than expected.
Block the knitted pieces before seaming. Pieces that are joined while still curled or uneven will not match in length, and the seam will pull the garment out of shape no matter how neatly it is sewn.
Finishing and pressing sweater seams
Sweater seams are rarely pressed with an iron the way woven seams are. Instead, they are eased into shape with steam, holding the iron above the seam and letting the steam relax the fibres, then leaving the seam to cool flat. Pressing directly with weight can flatten the knitting and leave a shiny mark. The seam allowances are usually left as they are, since the knitting does not fray, and trimming them close is not needed. A seam that has been steamed and left to cool will lie flatter and feel softer than one that was pressed hard, and the knitting keeps its spring.
After seaming, hang the sweater for a day and check the seams. A seam that has stretched can be corrected by adding a stabiliser, and a seam that puckers can be eased out and resewn. A sweater whose seams are checked this way keeps its shape far longer than one that is worn straight from the seaming table.