How to Press Seams on Knits
Knits stretch, and that is both their comfort and their problem at the ironing board. Press them gently, with the iron lifted and lowered, and the seams keep their shape.
Why knits need a different approach
A knit fabric is made of loops, not a woven grid, so it stretches in every direction and it does not spring back the way a woven fabric does. Heat and pressure can stretch it out of shape, and a stretched knit seam is hard to fix, because the fabric has been pulled longer than it was sewn. Sliding an iron across a knit seam is the fastest way to distort it: the iron pushes the fabric ahead of it, and the seam grows longer with every pass. Pressing, which lifts the iron and lowers it without sliding, avoids this entirely.
Knits are also sensitive to heat. Many knit fabrics contain synthetic fibres that can melt or shine under a hot iron, and some can be damaged by steam. The temperature that suits a cotton knit may be too hot for a fine jersey, so the iron setting should match the fibre, not the habit. A scrap test is worth the minute it takes.
Heat, steam, and the press cloth
Set the iron to a low or medium temperature, and test it on a scrap of the same fabric before touching the garment. If the fabric is a cotton knit, a little steam helps the seam settle. If it is a synthetic knit, steam may not be needed, and a dry press with a cloth may be safer. A press cloth, a piece of plain cotton or muslin laid between the iron and the garment, protects the knit from shine and from direct heat. It also stops the iron from sticking to any fusible interfacing used in the garment, which is common at necklines and hems on knits.
Press in short holds rather than long ones. Place the iron down, hold it for a few seconds, and lift it straight up. A long hold can flatten the loops of the knit and leave a mark, while a short hold sets the seam without pressing the texture out of the fabric. If the knit has a raised texture, like a rib or a cable, a press cloth and a very light touch keep the texture from being flattened, and the seam can be pressed from the wrong side so the right side is never touched by the iron at all.
Pressing a knit seam flat
- Lay the seam flat on the board and open the allowances with your fingers.
- Place a press cloth over the seam.
- Set the iron to a low or medium heat and press down for a few seconds, then lift straight up.
- Work along the seam in short sections, lifting and lowering the iron each time.
- Leave the seam to cool flat before moving the fabric.
Cooling matters on knits more than on wovens, because a warm knit is at its most stretchable. Moving the fabric while it is still warm can pull the seam out of shape, undoing the press that was just done. Letting it cool on the board locks the shape in.
Seams that are pressed to one side
On knits, many seams are pressed to one side rather than open, because the seam allowances on a knit are often narrow and the fabric is soft enough that an open press does not hold well. A seam pressed to one side also keeps the bulk together, which can help a knit seam lie smoothly. The method is the same: fold both allowances to one side, cover with a press cloth, and press with the iron lifted and lowered. On a garment, the allowances are usually pressed toward the back, or toward the side that will be hidden when the garment is worn. Hems on knits need the same gentle treatment. A hem folded up and pressed with a cloth, in short holds, keeps its shape without stretching the edge, while a hem pressed with the iron slid along it can grow longer on one side and hang unevenly.
Overlocked or serged seams on knits are often pressed to one side as well, since the overlocked edge is bulky and opening it can make the seam splay. A light press, with a cloth, is enough to set it.
Common problems on knits
Shine is the most visible problem: a glossy mark left by the iron on the surface of the fabric. A press cloth prevents it, and a lower temperature reduces it. Stretching is the second problem, and it shows as a seam that is longer after pressing than it was after sewing. The cause is usually sliding the iron, and the fix is to press with a lifting motion and to let the seam cool before moving it. A wavy seam, where the edge of the fabric ripples, can come from pressing a seam that was sewn with the fabric stretched, and in that case the seam may need to be re-sewn rather than re-pressed.
Ribbed knits need extra care at the iron, because the ribs can be flattened by heat and pressure. Press a ribbed cuff or hem from the wrong side, with a press cloth, and use a light touch with short holds. Pressing from the right side flattens the ribs and leaves a smooth patch that does not match the rest of the fabric. A rib that has been flattened is hard to bring back, so the wrong side and the cloth are the protection that keeps the texture intact.
Pressing knits is a gentle job. Low heat, a cloth, a lifting motion, and a cool-down before the fabric moves are the whole method, and they are enough to keep a knit seam flat, smooth, and the length it was sewn.