Seam Puckering on Knits
Knits pucker for reasons that are partly different from wovens. The loops stretch, the layers shift, and a stitch that is too tight or too straight can pull the fabric in along the seam line.
Why knits pucker
A knit is a structure of interlinked loops, and those loops move under the needle in ways that woven yarns do not. When a straight stitch is sewn on a knit, the stitches do not stretch with the fabric, so the seam can pull the loops in and leave a gathered line. A sharp needle can cut the loops instead of slipping between them, which weakens the seam and leaves small holes that distort the surrounding fabric. Tension that is too tight has a stronger effect on knits than on wovens, because the fabric itself gives way under the pull of the thread.
Feeding is another factor. Knits stretch easily, so pulling the fabric from behind the needle stretches the lower layer, and pushing it from the front bunches the top layer. The two layers can end up different lengths even on a short seam. A knit that is cut on the bias, or a lightweight jersey that curls at the edges, shifts more readily still. The result is a seam that looks wavy or gathered, even when the machine settings were correct for a woven fabric of the same weight.
Needle and stitch choices
The needle is the first thing to change on knits. A ballpoint needle slips between the loops instead of piercing them, which keeps the structure intact and reduces distortion. A stretch needle, with a slightly different point shape, suits very stretchy knits and elastic fabrics. Use a fresh needle, because a blunt point pushes loops aside and can start a pucker. Needle size should suit the fabric weight: a fine needle for lightweight jersey, a larger one for a heavy sweater knit.
Stitch choice matters as much as the needle. A narrow zigzag, a stretch stitch, or a serger stitch allows the seam to stretch with the fabric instead of pulling against it. A straight stitch can work on a stable knit with little stretch, but it is the stitch most likely to pucker on a stretchy one. Test the chosen stitch on a scrap, stretch the scrap gently after sewing, and check whether the seam lies flat and whether the stitches hold without breaking.
Stabilising the seam
Stabilising helps where the knit is light, curly, or prone to stretching. A strip of lightweight fusible interfacing, a strip of knit stay tape, or a length of clear elastic sewn into a shoulder seam can hold the seam line steady while the stitches form. The stabiliser should match the stretch of the fabric: a stabiliser with no stretch on a stretchy knit will make the seam stiff and can cause a different kind of distortion. For shoulder seams, which carry weight and are prone to stretching, a stabiliser is often the difference between a seam that holds its shape and one that grows longer with wear.
Tissue paper or a wash-away stabiliser under the seam can also help on very light jersey, by keeping the fabric from being pushed into the needle plate. Remove it gently after stitching. Pinning helps too, but pins should be placed across the seam line and used with a light hand, because pins can distort a knit if they are pushed through stretched fabric.
Feeding and pressing knits
Even feeding is harder on knits because the fabric stretches under its own weight and under the presser foot. Support the fabric on the table so its weight does not pull the seam as it feeds, and guide it lightly without pulling or pushing. A walking foot feeds the top layer at the same rate as the feed dogs feed the lower layer, which reduces the difference in layer length that causes puckering. Reducing presser foot pressure, where the machine allows it, also helps, because less pressure means less drag on the top layer.
- Fit a fresh ballpoint or stretch needle suited to the fabric weight.
- Choose a stretch stitch and test it on a scrap of the same knit.
- Pin or stabilise the seam, then sew at a steady, moderate speed.
- Press the seam with steam and a pressing cloth, without stretching it.
Pressing knits needs a light touch. Press with steam and lift the iron rather than sliding it, because sliding stretches the seam and can set a pucker in place. Use a pressing cloth to protect the surface, and let the seam cool completely before moving the piece. If a seam still puckers after these steps, check the thread. A thread that shrinks with heat can pull a knit seam in after pressing, even when the seam looked flat at the machine.
Testing before the real seam
A test seam on a scrap of the same knit is worth more on knits than on almost any other fabric, because knits vary so much in weight, stretch, and recovery. Sew the test with the same layers, the same stitch, and the same needle that will be used on the garment. Stretch the test seam gently in both directions and look at how it recovers. If the seam puckers when stretched, the stitch is too tight or too straight for that knit. If the seam lies flat but the stitches break when stretched, the stitch needs more give. Adjust one setting, test again, and keep a note of the combination that worked for that fabric, because the next knit will probably need a different one.