How to Press Seams Flat
A flat seam starts at the ironing board, not at the sewing machine. Open the allowances, press with the iron lifted and lowered, and let the seam cool.
Set up before the iron touches the fabric
Start with a clean ironing board and an iron set to a temperature that suits the fabric. Cotton and linen take more heat, wool takes moderate heat with steam, and synthetics need a lower setting. If the fabric is unfamiliar, test the iron on a scrap first, because a scorch mark cannot be undone. Have a press cloth nearby: a piece of plain cotton or muslin that sits between the iron and the garment and protects the fabric from shine and from direct heat. A spray bottle of water is useful for fabrics that need a little extra moisture, though steam from the iron does the same job on most cloth.
The seam itself should be ready. Finger press it first, running a thumbnail or a finger along the seam to open the allowances and crease the fold. This gives the iron a head start and makes the final press more even.
Pressing a seam open
Pressing a seam open means opening the two seam allowances apart, one to each side, and pressing them flat. It is the most common way to press a seam, and it gives the flattest result.
- Lay the seam flat on the board with the right side down and the allowances open.
- Place the iron on the seam, hold it for a few seconds, and lift it straight up.
- Work along the seam in sections, lifting and lowering the iron each time.
- Turn the work over and press lightly from the right side, using a press cloth if the fabric is delicate.
- Leave the seam to cool flat before moving it.
The iron should never slide across the seam. Sliding pushes the fabric and can stretch the seam out of shape, especially on a bias edge or a curve. Lifting and lowering keeps the fabric exactly where it was sewn.
Pressing a seam to one side
Some seams are pressed to one side, with both allowances folded together in the same direction. This is common on quilt tops, where seams are pressed toward the darker fabric, and on garments where the seam will be topstitched or enclosed. The method is the same: lay the seam flat, fold both allowances to one side, and press with the iron lifted and lowered. A seam pressed to one side is slightly bulkier than one pressed open, because two layers of allowance sit together, but it is stronger in some constructions and it keeps the seam from showing through on the right side.
On a quilt top, pressing to one side also helps the seams nest together when blocks are joined, so the points match more accurately. The direction of the press matters, and it is worth deciding before the seam is sewn, because a seam pressed the wrong way can be hard to change once the next seam is in place.
Keeping the allowance from showing through
A common problem is the edge of the seam allowance pressing a ridge into the right side of the fabric. It shows as a line running alongside the seam, and it is hard to remove once it is set. The cause is pressing the seam on a hard, flat surface, where the edge of the allowance is pressed into the cloth above it. The fix is to support the seam: a seam roll, a rolled towel, or a sleeve roll placed under the seam lifts the garment away from the board so only the seam itself is pressed. The allowance hangs free on either side and leaves no mark.
On light fabrics, the allowance can also show through as a shadow, even without a ridge. Pressing the seam open, rather than to one side, reduces this, because a single layer of allowance shows less than two. A press cloth between the iron and the fabric also helps, since it softens the pressure.
Seams that will not lie flat
Some seams resist pressing flat, and the reason is usually bulk rather than technique. A curved seam needs to be clipped or notched before it will lie flat, because the allowance is longer on one side of the curve than the other. A thick seam, like one through several layers of denim, needs to be graded, with the allowances trimmed to different widths, so they step down instead of stacking up. A seam with interfacing may need more heat and a longer press, since the interfacing holds its shape until it is warmed through. Darts behave the same way: a dart pressed flat from the point toward the wide end lies smoothly, while one pressed in the wrong direction can leave a small bubble at the tip that is hard to remove.
On striped or checked fabric, pressing needs an extra check: the pattern should match across the seam. Before pressing, line the stripes or checks up on either side of the seam and hold them in place while the iron sets the seam. Pressing a seam where the pattern does not match locks the mismatch in, and the eye is drawn to a stripe that steps sideways at a seam. A quick look at the pattern before the iron goes down is a small step that makes a visible difference on patterned cloth.
A flat seam is the result of a few small habits: the right heat for the fabric, the iron lifted rather than slid, the allowance supported, and the seam left to cool. None of them is difficult on its own, and together they make a visible difference to how a finished piece looks.