The Seam Line How seams are made, finished, and fixed

Home / Seam Pressing: How to Press Seams Well

Seam Pressing: How to Press Seams Well

Pressing is what makes a seam lie flat, sit straight, and look finished. It is one of the quietest skills in sewing, and one of the most visible in the result.

What pressing is

Pressing is not ironing. Ironing slides the iron across fabric to smooth out wrinkles. Pressing lifts the iron, places it down on the seam, holds it for a moment, and lifts it again. The weight of the iron and the heat do the work, and the fabric is not pushed or stretched while it happens. That distinction matters, because sliding an iron across a seam can stretch it out of shape, especially on bias edges and knits, while pressing sets the seam exactly where it was sewn.

A seam that has been pressed looks different from one that has not. The stitching sits flat, the two layers of fabric lie together without a ridge, and the garment hangs the way the pattern intended. A seam that has not been pressed shows its stitching as a small ridge, and the garment can look homemade in the unflattering sense: slightly puffy along every seam, with edges that curl instead of lying flat.

When to press

Pressing happens at every stage of sewing, not only at the end. Each seam is pressed as soon as it is sewn, before the next seam is added. This is sometimes called pressing as you go, and it is what keeps a garment accurate. A seam that is not pressed before the next piece is joined can pull the next seam off line, because the unpressed seam adds bulk and changes where the fabric folds. By the time a garment is finished, the difference between one that was pressed at each stage and one that was pressed only at the end is obvious.

Pressing also happens before sewing, when a fold or a crease needs to be set, and after sewing, when a hem or a facing is turned and needs to lie flat. The iron is used throughout the process, and the sewing machine and the iron share the work almost equally.

The basic method

The method is simple, and it is the same for most seams. Open the seam, lay it flat, and press it with the iron lifted and lowered, not slid.

  1. Open the seam allowances and lay the seam flat on the ironing board, right side down.
  2. Set the iron to a temperature that suits the fabric, and use steam if the fabric allows it.
  3. Place the iron down on the seam, hold it for a few seconds, and lift it straight up.
  4. Move the iron to the next section and repeat, working along the seam.
  5. Leave the seam to cool flat before moving the fabric, since a warm seam can shift.

Cooling matters more than it seems. A seam that is moved while it is still warm can lose the shape the iron just set, because the fibres have not yet settled. Letting it cool on the board, or on a flat surface, locks the press in place.

Steam and the press cloth

Steam helps the heat reach into the fibres of the fabric, and it is useful on cotton, linen, and wool. On delicate fabric, steam can leave a shine or a water mark, so a press cloth is used: a piece of plain cotton or muslin laid between the iron and the garment. The cloth protects the fabric from direct heat and from shine, and it also protects the iron from fusible interfacing, which can melt onto the soleplate. A press cloth is a simple tool, and it is the difference between a delicate fabric that is pressed safely and one that is marked by the iron.

Some fabrics should be pressed with little or no steam, and some should not be pressed at all without a cloth. When the fabric is unfamiliar, testing the iron on a scrap first is the safe approach. A scrap test takes a minute and can save a garment.

Tools that help

The iron is the main tool, but a few others make pressing easier. A tailor's ham is a curved cushion for pressing curved areas, like the bust or the hip, and a sleeve roll is a narrow cushion for sleeves and narrow seams. A seam roll, a long narrow cushion, supports a seam so it can be pressed without the impression of the seam allowance showing through to the right side. A wooden clapper, a flat block of wood, is pressed onto a seam after the iron to flatten it further and hold the heat in the fabric while it cools. None of these are required for a first project, but each one solves a specific problem that the flat ironing board cannot.

Pressing different fabrics

Different fabrics ask for different heat, and the iron setting should match the cloth. Cotton and linen take a hot iron with steam, and they press crisply. Wool takes moderate heat with steam, and it holds a press well once it cools. Silk and other delicate fabrics need a low heat and a press cloth, because the iron can leave a shine or a mark on them. Synthetic fabrics need the lowest heat of all, since they can melt or glaze under a hot iron, and a scrap test is the safest way to find the right setting. When a garment mixes fabrics, such as a cotton body with a silk lining, each part is pressed at the setting that suits its own fabric, and the press cloth protects the more delicate one.

The weight of the fabric matters too. A heavy fabric needs a longer press and more steam to set the seam, while a light fabric needs only a short hold. Pressing a light fabric the way a heavy one is pressed can flatten it and leave a mark, and pressing a heavy fabric the way a light one is pressed will not set the seam at all. Watching how the fabric responds, and adjusting the heat and the hold to suit it, is the skill that ties the whole method together.

Common pressing problems

The most common problem is a seam allowance that shows through to the right side of the fabric as a ridge. This happens when the seam is pressed on a hard surface without support under it, and the edge of the allowance presses a line into the fabric. A seam roll or a folded towel under the seam prevents it. Another common problem is shine, a glossy mark left by the iron on dark or delicate fabric, which a press cloth prevents. A third is a seam that will not lie flat, which usually means the seam needs to be graded or clipped before pressing, or that the fabric needs more steam and a longer press.

Pressing is a skill that improves with attention rather than with equipment. Watching how the fabric responds to the iron, and adjusting the heat, the steam, and the pressure to suit it, is what turns a pressed seam from adequate into good.

The habit to build is simple: press each seam as it is sewn, lift the iron instead of sliding it, and let the seam cool before moving it. Those three habits are the foundation of every well-pressed garment.