Pressing Seams with a Ham and Roll
A flat ironing board cannot press a curved seam properly, because the curve needs support underneath it. That is the job of the ham and the sleeve roll.
What a tailor's ham is
A tailor's ham is a firmly stuffed cushion, shaped like a ham, with a curved surface. It is used to press curved areas of a garment, such as the bust, the hip, or a curved seam, where a flat board would flatten the shape the seam is meant to hold. The garment is laid over the curve of the ham, so the seam follows the cushion instead of being pressed flat against a board, and the iron presses the seam while the shape underneath is preserved.
A ham usually has two sides: one covered in cotton and one in wool. The cotton side is used for most pressing, and the wool side holds heat and steam longer, which suits wool fabric and seams that need a firm press. The shape is the important part, though, not the covering. The curve of the ham matches the curve of the body, and that is what makes it work.
What a sleeve roll is
A sleeve roll is a long, narrow, firmly stuffed cushion, shaped like a sausage. It is used for pressing sleeves and narrow seams, where the fabric needs to be slipped over a support so the seam can be pressed without pressing the other side of the tube at the same time. A sleeve slipped over the roll can be pressed one side at a time, with the roll holding the sleeve open, and the seam allowance can be pressed without leaving a crease on the opposite side of the sleeve.
The same roll works for narrow seams anywhere on a garment: trouser legs, small collars, cuffs, and the narrow seams on children's clothes. Any place where a seam sits inside a tube, or where the fabric is too narrow for the ironing board, is a place where the sleeve roll helps.
Pressing a curved seam on the ham
- Lay the curved seam over the ham so the curve of the seam follows the curve of the cushion.
- Open the seam allowances and finger press them into place.
- Press with the iron lifted and lowered, using steam if the fabric allows it.
- Work along the curve in short sections, moving the garment as needed so the seam stays supported.
- Leave the seam on the ham to cool, so the curve sets before the fabric is moved.
The key is to keep the seam supported the whole time. If part of the seam hangs off the ham and is pressed on the flat board, that part will be flattened and the curve will be uneven. Moving the garment along the ham as the pressing progresses keeps the support under the section being pressed. Darts are pressed on the ham in the same way, with the point of the dart at the narrow end of the cushion and the wide end over the curve, so the dart keeps its shape instead of being flattened into a crease.
Pressing a sleeve on the roll
- Slip the sleeve over the roll so the seam sits on top of the cushion.
- Open the allowances and press the seam with the iron lifted and lowered.
- Turn the sleeve around the roll to press the next section, keeping the seam on top.
- Check that no crease has been pressed into the underside of the sleeve.
- Leave the sleeve on the roll to cool.
On a set-in sleeve, the sleeve cap is curved, and it can be pressed on the ham first, before the sleeve is slipped over the roll for the long seam. The two tools work together: the ham for the curved cap, the roll for the straight seam.
Other pressing supports
A seam roll is a longer, narrower version of the sleeve roll, used for pressing long straight seams without the allowance showing through to the right side. The seam sits on top of the roll, the allowances hang free on either side, and the iron presses only the seam. A wooden clapper, a flat block of wood, is pressed onto a seam after the iron to flatten it further and hold the heat while the fabric cools. A point presser, a narrow wooden tool with a pointed end, supports collars and cuffs while they are pressed. Each of these solves a small problem that the flat board cannot, and together they cover most of the shapes a garment can take.
None of these tools is required for a first project. A rolled towel can stand in for a sleeve roll, and a firmly stuffed cushion can stand in for a ham. But when curved seams and narrow tubes become a regular part of the work, the proper tools make the pressing faster and the results more consistent. A tailor's board, a small narrow board that sits on a table, is another useful support: it works like a small ironing board for sleeves, narrow seams, and small pieces that would be awkward on a full-size board.
A collar is pressed on the ham in much the same way as a curved seam. The collar is laid over the curve with the seam at the top, the allowances are opened, and the iron presses the seam while the curve of the ham holds the shape of the collar. A collar pressed flat on a board can lose its roll and sit stiffly against the neck, while one pressed on the ham keeps the gentle curve it was cut with. The same method suits a curved yoke or a shaped facing, anywhere the fabric is meant to curve rather than lie flat.
The ham and the roll are not luxuries. They are the tools that let a curved seam keep its curve and a sleeve keep its shape, and a garment pressed on them looks noticeably better than one pressed flat on a board.