Curved Seam Pressing
Pressing is what makes a curved seam lie flat and keep its shape, and it works when the seam is pressed over a curved surface, not flattened on the board.
Why pressing matters on a curve
Pressing does more than remove creases. On a curved seam, it sets the fibres in the shape of the curve, so the seam keeps that shape when the garment is worn. A curved seam that is pressed well lies flat, follows the body, and shows no puckering. A curved seam that is pressed badly, or not pressed at all, pulls, bunches, and distorts the garment, even if the stitching was accurate.
The reason is that fabric fibres relax under heat and steam, and they set in the shape they cool in. Pressing a curved seam over a curved surface lets the fibres set in the curve. Pressing the same seam flat on the board forces the fibres to set in a flat shape, and the seam then fights the curve every time the garment moves. The pressing surface matters as much as the iron.
Pressing is also the step that reveals whether the seam was sewn well. A well sewn curved seam presses flat and smooth with little effort. A poorly sewn one, with uneven easing or an unclipped allowance, resists pressing and keeps puckering. That is useful information, because it shows the problem while it can still be fixed, rather than after the garment is finished.
Tools for pressing curves
A tailor's ham is the main tool for pressing curved seams. It is a firm cushion, shaped like a ham, with a wool side and a cotton side, and it supports a curve while it is pressed. The seam sits over the ham, the iron presses it, and the curve keeps its shape. A ham is used for shoulder seams, bust curves, sleeve caps, and any curve that needs a rounded support.
A sleeve roll is a long, narrow cushion that fits inside a sleeve or a trouser leg, and it is used for pressing long curved seams, such as the underarm seam of a sleeve. A seam roll, which is similar but shorter, is used for pressing a seam open without leaving an imprint on the right side. A rolled towel is a workable substitute for any of these, if the proper tools are not available, though it is softer and less firm than a ham.
A press cloth protects the fabric from the iron, and it is worth using on wool, silk and dark fabrics, where a hot iron can leave a shine. A press cloth also lets steam reach the fabric without the iron touching it directly, which is useful on delicate curves. The cloth should be cotton, and it should be dampened lightly for steam pressing.
Pressing a curved seam step by step
- Press the seam as sewn first, with the stitching line flat, to set the stitches.
- Open or fold the allowance as the pattern directs, then place the curve over a ham or a sleeve roll.
- Press with steam, holding the iron on the seam rather than sliding it, which can stretch the curve.
- Let the seam cool in shape on the ham before moving it, so the fibres set in the curve.
- Turn the garment and check the right side for a smooth curve with no ridge or pucker showing.
Pressing as sewn, before opening the seam, is a step that is easy to skip and worth doing. It sets the stitches into the fabric and flattens the seam line, which makes the next steps easier. The seam is pressed from the wrong side, with the iron resting on the stitching line, and the fabric is not stretched while it is pressed.
Holding the iron still, rather than sliding it, is the other habit that matters. Sliding the iron pushes the fabric and stretches the curve, especially on a bias cut. Lifting the iron, moving it to the next section, and pressing down again, known as press and lift, keeps the fabric in place and the curve true. It is slower than ironing, but pressing a seam is not ironing, and the difference shows in the result.
Pressing different curves
An outward curve, such as a sleeve cap, is pressed over the rounded end of the ham, where the surface curves outward to match. An inward curve, such as an armhole, is pressed over the side of the ham, or over a sleeve roll, where the surface curves inward. The point is to match the pressing surface to the curve, so the seam is supported in its own shape.
A long, gentle curve, such as a princess seam, can be pressed over the length of the ham, moving the seam along as each section is pressed. A short, tight curve, such as a neckline, needs the narrow end of the ham, or a small rolled towel, so the support fits inside the curve. Using a support that is too large for the curve flattens it, and using one that is too small leaves part of the seam unsupported.
Thick fabrics need more steam and a firmer press than fine fabrics, and they need longer to cool. Fine fabrics need a lighter press, a press cloth, and a lower heat, because they scorch easily. The iron setting should suit the fabric, and a scrap test is the reliable way to check it before pressing the real seam.
Fixing a curve that will not press flat
A curved seam that will not press flat usually has a problem in the sewing, not in the pressing. The first thing to check is whether the allowance was clipped or notched enough. An outward curve that still pulls needs more clips. An inward curve that still bunches needs more notches. Adding the missing cuts, then pressing again, usually solves it.
The second thing to check is the easing. If the easing was uneven, the fullness bunches in one place, and no amount of pressing will spread it. The fix is to unpick the section, re ease it evenly, and restitch. The third thing to check is whether the fabric was stretched while stitching. A stretched curve grows longer than it should be, and the extra length puckers. Staystitching before sewing prevents this, but once the seam is sewn, the repair is to unpick and restitch with the fabric handled gently.
Steam can fix a mild problem. Holding the iron just above the fabric and letting the steam relax the fibres, then pressing gently and letting the seam cool in shape, can settle a pucker that is caused by handling rather than by sewing. A pucker that survives steam, a ham, and a cooling period is sewn in, and the seam should be unpicked and restitched. That is a small repair, and it is better than a garment with a permanent pucker along a visible curve.