The Seam Line How seams are made, finished, and fixed

Home / Curved Seams: How They Work and How to Sew Them

Curved Seams: How They Work and How to Sew Them

Curved seams turn flat fabric into a shaped garment, and they work when the fabric is eased around the curve, clipped where needed, and pressed over a curved surface.

What a curved seam does

A curved seam joins two pieces of fabric along a line that is not straight. That curve is what gives a garment its shape. A princess seam curves over the bust, an armhole curves around the shoulder, a neckline curves around the throat, and a sleeve cap curves over the top of the arm. Without curved seams, a garment made from flat cloth would hang like a tube. With them, the cloth follows the body.

The challenge of a curved seam is that the two sides of the curve behave differently. On an outward curve, the outer edge of the seam allowance is longer than the stitching line, so it needs to spread out. On an inward curve, the outer edge is shorter than the stitching line, so it needs to close up. If the allowance is left as cut, it bunches on an inward curve and pulls on an outward curve, and the finished seam puckers or stands away from the body.

That is why curved seams need the extra steps that straight seams do not: easing, clipping, notching and pressing over a curved surface. Each of those steps deals with the difference in length between the stitching line and the edge of the allowance, and together they let the seam lie flat and follow the shape it was cut to give.

Easing a curve

Easing means distributing a slightly longer edge along a slightly shorter one, so the fullness is spread evenly and invisibly. It is used where the two pieces being joined have curves of slightly different lengths, such as a sleeve cap eased into an armhole. The longer edge is gathered very slightly, with the gathers spread so finely that they disappear into the seam, and the two edges are pinned together before stitching.

The key to easing is that the fullness should be invisible in the finished seam. If the gathers show as tiny folds on the right side, the easing was too concentrated in one place. Spreading the pins evenly, and stitching slowly with the fuller side on top so it can be watched, helps keep the easing even. A little steam after stitching also helps the eased fullness settle into the seam.

Staystitching helps too. A line of stitching just inside the seam line, sewn before the pieces are joined, stops a curved edge stretching out of shape while it is handled. This matters most on bias curves and on fabrics that stretch, such as silk and rayon, where the curve can grow by a noticeable amount between cutting and sewing. The staystitching sits inside the allowance, so it never shows.

Clipping and notching

Clipping and notching are the standard ways to let a seam allowance follow a curve. On an outward curve, small clips are cut into the allowance, at right angles to the stitching line, so the allowance can spread open. On an inward curve, small notches, which are V shaped cuts, are taken out of the allowance, so it can close up without bunching. Both are done after stitching, and both stop short of the stitching line so the seam is not weakened.

The spacing of the clips or notches depends on how tight the curve is. A gentle curve needs only a few, spaced widely apart. A tight curve needs many, spaced closely. The test is whether the seam lies flat after pressing. If it still pulls or bunches, more clips or notches are needed. If the seam lies flat, the number is right.

Grading the allowance, which means trimming one side of the allowance shorter than the other, also helps a curved seam lie flat, especially where the fabric is thick. The shorter layer sits underneath, and the longer layer covers it, so the edge of the allowance does not show as a ridge on the right side. Grading is often combined with clipping or notching on a curved seam in a medium weight fabric.

Sewing a curved seam

  1. Staystitch any curve that is cut on the bias or in a stretchy fabric, just inside the seam line.
  2. Pin the pieces together along the curve, placing pins at right angles to the stitching line.
  3. Stitch slowly, guiding the curve gently and stopping with the needle down to reposition the fabric when needed.
  4. Clip outward curves or notch inward curves in the allowance, stopping short of the stitching line.
  5. Press the seam over a tailor's ham or a rolled towel, so the curve keeps its shape.

Stitching slowly is the most useful habit on a curve. The machine feeds the fabric in a straight line, and the sewer's job is to guide the curve through the foot without stretching or forcing it. Short seams can be sewn in one pass, but on a long curve it helps to stop, lift the presser foot with the needle down, and turn the fabric slightly before continuing. That keeps the stitching on the marked line instead of drifting wide on the curve.

Pinning matters more on a curve than on a straight seam, because the two edges want to shift apart. Pins placed across the seam line, at right angles, hold the layers together without distorting the curve. Pins placed along the seam line can pull the fabric and change the shape of the curve, so they are best avoided here.

Pressing a curved seam

Pressing a curved seam flat on the board distorts it, because the board is flat and the seam is not. A tailor's ham, which is a firm cushion shaped like a ham, supports the curve while it is pressed, so the seam keeps its shape. A sleeve roll, which is a long narrow cushion, does the same for a sleeve seam. A rolled towel is a workable substitute for either, if no pressing ham is available.

Press the seam from the wrong side first, with the curve sitting over the ham, and use steam to help the fibres settle. Let the seam cool in shape before moving it, because a warm seam can be pulled out of shape while it is still soft. Then check the right side. The curve should lie smooth, with no puckering and no ridge showing through from the allowance.

If the seam still puckers after pressing, the cause is usually in the stitching or the clipping, not the pressing. A pucker that will not press out means the allowance was not clipped enough, the easing was uneven, or the fabric was stretched while stitching. Pressing can settle a mild pucker, but it cannot fix a seam that was sewn wrong, and the honest repair is to unpick and restitch it.