The Seam Line How seams are made, finished, and fixed

Home / How to Sew a Curved Seam

How to Sew a Curved Seam

A curved seam is sewn slowly, with the fabric guided rather than pushed, and it is finished by clipping the allowance and pressing the curve over a ham.

Getting ready

Start by looking at the curve. Is it an outward curve, where the seam bulges toward the sewer, or an inward curve, where it dips away? Is it gentle, changing direction over a long distance, or tight, turning sharply over a short one? The answers decide how much easing, clipping and pressing the seam will need. A gentle outward curve on a stable fabric needs little extra work. A tight inward curve on a stretchy fabric needs all of it.

Check the pattern markings. Notches and dots on the pattern pieces show where the curves should match, and lining those marks up before pinning keeps the seam from drifting. If the pieces are pinned without matching the marks, one side of the curve can end up longer than the other, and the seam will pucker where the extra length has nowhere to go.

Choose the right tools. Fine pins, placed across the seam line, hold a curve without distorting it. A tailor's ham or a rolled towel supports the curve during pressing. A seam ripper should be close at hand, not because mistakes are expected, but because a curved seam that is unpicked and restitched is a small repair, while a curved seam that is forced is a spoiled garment.

Staystitching and pinning

Staystitch the curve before joining the pieces if the fabric is prone to stretching. Staystitching is a line of regular stitching sewn just inside the seam line, on a single layer of fabric, and its job is to stop the curve stretching out of shape while it is handled. It is especially useful on bias curves and on silk, rayon and other fabrics that grow easily. The staystitching sits inside the allowance, so it never shows on the finished garment.

Pin the pieces together along the curve, with the pins at right angles to the stitching line. Start at the pattern marks and work outward, easing the two edges together as you go. If one edge is slightly longer than the other, spread the extra length evenly between the pins, rather than letting it bunch up at one end. The pins should be close enough that the layers cannot shift while stitching, which on a tight curve means a pin every few centimetres.

For a sleeve cap or an armhole, where one edge is deliberately longer than the other, the easing needs to be spread with particular care. The fullness should be distributed evenly across the top of the cap, with none of it concentrated at the front or the back. Pinning from the centre outward, on both sides, helps keep the easing balanced.

Stitching the curve

  1. Place the pinned pieces under the presser foot with the seam line aligned to the needle.
  2. Stitch slowly, guiding the fabric with both hands and letting the feed dogs move it.
  3. Stop with the needle down and lift the presser foot to reposition the fabric when the curve turns.
  4. Keep the stitching on the marked seam line, checking the guide marks as you go.
  5. Backstitch a few stitches at the end to secure the thread.

The habit that matters most is letting the machine do the feeding. Pushing the fabric through the foot, or pulling it from behind, stretches the curve and changes its shape. Guiding means keeping the fabric flat and on line, with light hands, while the feed dogs move it forward. On a tight curve, the fabric needs to be turned slightly as it goes, and stopping with the needle down to reposition is the way to do that without stretching.

Stitch length deserves a thought too. A very long stitch can let a curved seam gap open, because the stitches are too far apart to hold the curve. A very short stitch can perforate a fine fabric. A medium length, tested on a scrap of the same fabric, is usually right. The scrap test is worth doing, because it also shows whether the tension is balanced and whether the fabric puckers under the foot.

Finishing the seam

After stitching, the allowance needs clipping or notching so the seam can lie flat. On an outward curve, cut small clips into the allowance at intervals, stopping short of the stitching line. On an inward curve, cut small V shaped notches out of the allowance. The tighter the curve, the closer together the clips or notches should be. Then press the seam over a tailor's ham or a rolled towel, so the curve keeps its shape while it is pressed.

Check the right side after pressing. The curve should lie smooth, with no puckering along the stitching line and no ridge showing through from the allowance. If there is a pucker, check whether the allowance was clipped enough and whether the easing was even. A mild pucker may press out with steam and a ham. A stubborn pucker means the seam needs unpicking and restitching, which is a small repair and a better result than living with a puckered curve.

Trimming and grading the allowance can also help, especially on a medium weight fabric. Trimming one side of the allowance shorter than the other, so the layers step down instead of stacking, stops the edge of the allowance showing as a ridge on the right side. This is called grading, and it is often done together with clipping or notching on a curved seam.

On a tight curve, stitch with the concave side up so the fullness can be seen and eased as it goes under the foot, rather than hidden underneath where it can bunch unseen.