The Seam Line How seams are made, finished, and fixed

Home / Seam Pressing and Bulk

Seam Pressing and Bulk

Bulk is the stack of fabric layers that sits under a seam, and it is the main reason a seam will not lie flat. Pressing alone cannot fix it, but pressing combined with trimming can.

What bulk is

Every seam has seam allowances, and every allowance is a layer of fabric. On a simple seam through two layers of cloth, pressing open leaves one layer of allowance on each side, which is not much bulk. But where seams cross, where a facing meets a seam, or where a thick fabric is used, the layers stack up: four, six, or eight layers in one spot. That stack is bulk, and it shows as a lump, a ridge, or a seam that refuses to lie flat.

Bulk is not a flaw in the sewing. It is a natural result of joining layers of fabric, and every garment has it somewhere. The work is in managing it, so the bulk sits where it does not show and does not distort the shape of the garment.

Grading: trimming in steps

Grading is the main way to reduce bulk. It means trimming the seam allowances to different widths, so they step down instead of stacking up at the same edge. The allowance closest to the garment is trimmed narrowest, and each layer is left a little wider than the one before it. The result is a stepped edge rather than a cliff, and the seam presses flatter because the bulk is spread over a wider area.

On a faced neckline, for example, grading the facing allowance shorter than the garment allowance lets the facing lie flat inside the garment without a ridge showing on the outside. On a collar, grading lets the collar turn smoothly without a hard edge. Grading is done after the seam is sewn and before it is pressed, and it takes only a few snips with scissors. On a lined garment, grading matters even more, because the lining adds another layer at every seam, and an ungraded lining seam can show through the outer fabric as a ridge that no amount of pressing will remove.

Trimming, clipping, and notching

Trimming cuts the allowances narrower overall, which helps on thick fabrics where even a graded seam is too bulky. Clipping cuts small notches into the allowance on an inward curve, so the allowance can spread and lie flat when the seam is turned. Notching cuts small triangles out of the allowance on an outward curve, so the excess fabric does not bunch up inside the curve. These are all done before pressing, and they are what make the press work. Pressing a seam that has not been clipped or graded is pressing against fabric that has nowhere to go.

It is worth being careful with clipping and notching: the cuts should stop short of the stitching, so the seam itself is not weakened. A cut that reaches the stitching can let the seam come apart, and a seam that has been clipped too close is weaker than one that has not been clipped at all.

Pressing in stages

Bulk is easier to manage when the pressing is done in stages. Press the seam first with the allowances together, to set the stitching, then open the allowances and press them flat. On a very bulky seam, pressing the allowances separately, one at a time, gives a flatter result than pressing them together. A wooden clapper, pressed onto the seam after the iron, helps flatten bulky seams further: it holds the heat in the fabric while it cools, which sets the press more firmly than the iron alone.

A seam roll under the seam also helps, because it supports the seam itself while the allowances hang free on either side. Without support, the bulk of the allowances presses a ridge into the right side of the fabric, and that ridge is hard to remove once it is set.

Where bulk gathers

Bulk gathers in predictable places. Where two seams cross, the allowances stack up and form a lump. Pressing the allowances in opposite directions at the crossing, so they nest together, reduces the lump. At a corner, the allowances fold over each other, and trimming the corner at an angle before turning it reduces the bulk inside the point. At a waistband or a cuff, where several layers are joined, grading is the main tool. At a zip, the tape and the seam allowances stack together, and pressing the allowances away from the zip keeps the area flat. Where a pocket is attached, the pocket bag and the garment layers meet at the seam, and grading the pocket allowance shorter than the garment allowance keeps the pocket from showing as a ridge on the outside.

On very thick fabric, such as denim or canvas, bulk may not press flat at all, even with grading. In that case, hammering the seam gently with a tailor's clapper, or pressing it with extra steam and a longer hold, can help, but the seam will always be thicker than a seam in a lighter fabric.

A wooden clapper helps on bulky seams, because it presses the seam flat and holds the heat in the fabric while it cools. After the iron has pressed the seam, the clapper is placed on top of it and left there for a few seconds, pressing the layers together while the fabric cools. The wood absorbs the moisture from the steam, which sets the press more firmly than the iron alone. On wool and cotton, the difference is easy to feel: a seam pressed with a clapper stays flatter for longer than one pressed with the iron only.

Bulk is managed, not eliminated. A garment will always have layers under its seams, and the goal is to spread those layers, trim them where they stack, and press them flat, so the outside of the garment stays smooth and the shape stays true.