The Seam Line How seams are made, finished, and fixed

Home / Denim Seam Bulk

Denim Seam Bulk

Bulk is the main enemy of a neat denim seam. Where several thick layers meet, the seam can go lumpy, skip stitches, and show through the fabric.

Where Bulk Comes From

Bulk builds up wherever layers stack. On jeans, the worst spots are the crotch join, where the inseams meet, the pocket corners, where the pocket, the facing, and the leg all cross, and the waistband, where the band, the leg, and the facing meet. Each layer adds thickness, and by the time four or five layers of heavy denim are stacked, the foot cannot sit flat and the needle struggles to get through.

Seam allowance adds to the problem. Every layer brings its own allowance, and those allowances stack up inside the seam. On a flat-felled seam, the folded allowance adds still more layers. The result is a ridge that shows through the fabric, rubs against the skin, and wears faster than the flat parts of the seam. Reducing that ridge is the whole job of managing bulk.

Trimming and Grading

Trimming cuts the seam allowance narrower, and grading cuts each layer to a slightly different width, so the edges step down instead of forming a single thick cliff. The widest layer sits closest to the fabric, and each layer above it is cut a little narrower, which spreads the thickness over a wider area and lets the seam lie flatter. Grading is the single most useful technique for bulk on denim, and it costs nothing but a careful pass with the scissors.

On a flat-felled seam, one allowance is trimmed close before the other is folded over it, which keeps the folded layers from stacking too high. On a plain seam, both allowances can be graded, and the topstitched side can be trimmed narrower still. The trimming should be done before pressing and topstitching, since a graded seam presses flatter and topstitches more evenly.

Pressing and Flattening

Pressing a denim seam flat before topstitching makes a real difference. The iron pushes the layers down and sets the fold, so the topstitching runs over a flat surface instead of a ridge. A tailor's clapper, a flat block of wood pressed onto the seam after ironing, holds the heat in and flattens the seam further. On very thick joins, a mallet can be used to tap the layers flat, a traditional technique that softens the fibres and compresses the bulk.

Pressing should be done on the wrong side where possible, with a cloth between the iron and the fabric if the denim is likely to shine. The seam should be pressed in the direction it will lie, so the topstitching follows the same line. A seam that is pressed flat before it is topstitched will stay flat; a seam that is topstitched over a ridge will keep that ridge.

A tailor's ham, a firmly stuffed curved cushion, helps press seams that curve, such as the crotch or the armhole of a denim jacket. The seam is laid over the curve of the ham and pressed, which lets the fabric follow its shape instead of being flattened against a board. For straight seams, a flat board and a clapper do the work, but for a curved seam the ham keeps the shape while the heat sets the fold.

Getting the Machine Over the Joins

The hardest moment in sewing a denim seam is getting the foot over a thick join. When the foot tips forward onto the high layers, the needle can skip, the stitching can wander, and the fabric can jam. A hump jumper, a small tool slipped under the back of the foot, levels the foot so it can climb onto the thick layers smoothly. A folded piece of fabric under the back of the foot does the same job in a pinch.

Sewing slowly over joins is just as important. Let the machine take its time, and turn the handwheel by hand if the needle struggles. A fresh heavy-duty needle made for denim helps here, since a blunt needle will push the layers instead of piercing them. Forcing the fabric through can bend or break the needle, so patience at the joins is part of the technique.

Design Choices That Reduce Bulk

Some bulk can be designed out before sewing starts. Placing a seam where fewer layers cross, trimming a facing before it is sewn in, or choosing a lapped seam instead of a folded one can all reduce the thickness at a join. On a pocket, the facing can be cut narrower so it does not reach the seam line, and on a waistband the allowances can be graded before the band is attached.

Seam allowance width also affects bulk. A wide allowance adds layers that have to be folded and pressed, while a narrow allowance leaves less to trim and grade. On a denim seam, the allowance should be wide enough to hold firmly and to allow grading, but no wider than it needs to be. Keeping the allowance consistent along the seam also helps, since an allowance that varies in width will press unevenly and the seam will lie flat in some places and ridge in others.

Not every join can be redesigned, and some bulk is unavoidable on heavy denim. The goal is not to remove all thickness, but to spread it, press it flat, and keep the seam lying smoothly. A seam that is graded, pressed, and topstitched carefully will feel flat and look neat, even where several layers meet.

Bulk is a fact of sewing denim, not a sign of failure. Trim it, grade it, press it flat, and take the joins slowly, and the seam will lie as smoothly as heavy fabric allows.