The Seam Line How seams are made, finished, and fixed

Home / Seams on Faux Leather

Seams on Faux Leather

Faux leather behaves like leather in most ways, but it is usually thinner, and it can melt under a hot iron. Seams on faux leather need the same care as leather seams, with low heat pressing and a longer stitch.

What faux leather is

Faux leather is a man made material designed to look and feel like leather. It is usually made by coating a fabric base with a plastic layer, which gives it a smooth surface and a leather like appearance. It is used for jackets, bags, skirts, and upholstery, often as a lower cost alternative to real leather.

Faux leather is usually thinner than real leather, which makes it easier to sew. It folds more easily, it needs less force to stitch, and the seams sit flatter. It is also more consistent in thickness than real leather, which varies across a hide. That consistency makes it easier to plan a seam.

The main difference from real leather is heat. Faux leather can melt or stick under a hot iron, and it can be damaged by high heat in other ways too. It also has a fabric backing, which behaves differently from the plastic surface. A seam on faux leather has to be planned with both layers in mind.

How it differs from real leather

Like real leather, faux leather shows needle holes. A hole punched in faux leather stays visible, and a seam cannot be unpicked and resewn without leaving marks. The same rule applies: test on a scrap, mark carefully, and stitch once.

Unlike real leather, faux leather is thinner and softer, which means the seams are easier to sew and the allowances sit flatter. A French seam, which is bulky on thick leather, is more practical on faux leather, since the double fold is thinner. A plain seam on faux leather is straightforward, and the allowance can often be pressed flat with a low heat iron and a press cloth.

Faux leather can also stretch. The fabric backing has some give, and the plastic coating can stretch under tension. A seam on faux leather should be sewn without pulling, and the pieces should be supported while they are sewn, so the seam does not stretch out of shape.

Choosing a seam

A plain seam is the most common seam on faux leather. Two pieces are placed together, stitched, and the allowances are pressed or glued to one side. The plain seam is simple, strong, and suits most faux leather work. The allowances are usually trimmed to reduce bulk, and they can be glued down if pressing is not safe.

A lapped seam is useful where a flat, strong join is needed. One piece overlaps the other, and the stitching goes through both layers. A lapped seam is flatter than a plain seam and very strong, which makes it useful on bags and belts made from faux leather.

A French seam is practical on faux leather, unlike on thick real leather, because the material is thin enough to fold twice without too much bulk. It encloses the raw edges, which is useful since the fabric backing of faux leather can fray. A French seam on faux leather gives a clean finish on a garment where the inside of the seam will be visible.

A topstitched seam, where the allowance is pressed to one side and stitched down from the outside, is common on faux leather jackets and bags. It holds the seam flat and adds a decorative line. Topstitching should be sewn slowly and evenly, since it is fully visible.

Sewing the seam

  1. Use a leather point needle or a sharp universal needle, and a strong polyester thread. Test both on a scrap first.
  2. Mark the seam line with chalk or a washable marker. Do not use a pen that could stain the surface.
  3. Hold the pieces together with clips or double sided tape, not pins, since pins leave holes in faux leather.
  4. Sew slowly with a longer stitch length than cloth needs, guiding the material without pulling it.
  5. Do not backstitch at the start or end. Leave long thread tails and finish them by hand.
  6. Trim the allowance to reduce bulk, and finish it by gluing it down or pressing it with low heat and a press cloth.

Pressing faux leather

Press faux leather with low heat and a press cloth. A hot iron can melt the plastic surface, leaving a shiny mark or a stuck patch that cannot be removed. Test the iron on a scrap first, starting at the lowest heat setting, and increase the heat only if the scrap shows no damage.

Use a press cloth between the iron and the faux leather, even at a low heat setting. The cloth protects the surface from direct contact with the iron, and it spreads the heat evenly. Press briefly, with the tip of the iron, rather than holding the iron down on the material.

Some faux leathers should not be ironed at all. If the scrap test shows damage even at a low heat setting, do not iron the item. Glue the seam allowances down instead, and tap them flat with a mallet. A seam finished with glue and a mallet is as flat as a pressed seam, and it carries no risk of melting.

Let the seam cool before moving the material. Faux leather holds the shape it is pressed into while it is hot, and moving it too soon can pull the seam out of shape. A few seconds of cooling is enough.

Test the iron on a scrap of the same faux leather before pressing the item. Some faux leathers melt at a low heat setting, and the damage cannot be undone.

Problems to watch for

Sticking is the most common problem when sewing faux leather. The plastic surface can stick to a standard metal presser foot, which causes the top layer to creep and the seam to go uneven. A Teflon foot, a roller foot, or a walking foot solves the problem. A little talcum powder on the surface can also help, though it should be brushed off afterwards.

Stretching is the second problem. The fabric backing of faux leather can stretch while it is sewn, especially on a bias or a curve. Sew slowly, guide the material without pulling, and support the pieces while they are sewn. A seam that has stretched will not press flat, and it should be unpicked and resewn, though the needle holes will remain.

Melting is the third problem, and it comes from pressing. A hot iron can melt the surface, and the damage is permanent. A press cloth and a low heat setting prevent it, and a scrap test before pressing the item is the safest habit. If in doubt, do not iron: glue the allowance down instead.

Faux leather is easier to sew than real leather, but it has its own risks. A longer stitch, clips instead of pins, a non stick foot, and low heat pressing will give seams that are strong, flat, and neat.