The Seam Line How seams are made, finished, and fixed

Home / French Seam on Leather

French Seam on Leather

A French seam on leather encloses the raw edges inside the seam, just as it does on cloth. The difference is bulk: leather does not fold and press the way cloth does, so a French seam on leather needs thin, soft leather and careful thinning of the allowance.

What a French seam does on leather

A French seam is sewn in two passes. The first pass joins the leather with wrong sides together, using a narrow allowance. The allowance is trimmed, the leather is folded so the right sides are together, and the second pass is sewn along the fold, enclosing the first stitching. The raw edges end up inside the seam, and the finished seam looks clean from both sides.

On cloth, the French seam is valued because it hides edges that would fray. Leather does not fray, so that advantage does not apply. On leather, the French seam is chosen for its look: a clean, enclosed seam with no raw edge showing. It suits a garment or a bag where the inside of the seam will be visible, and where a plain seam with a raw edge would look unfinished.

The seam is also strong. Two lines of stitching hold the leather together, and the enclosed allowance adds a little extra body to the seam. On a thin leather, that strength is useful. On a thick leather, the double fold is too bulky to be practical.

When it works, and when it does not

A French seam on leather works best on thin, soft leather. A soft lambskin, a thin goatskin, or a lightweight calfskin folds well enough for the second pass, and the finished seam sits reasonably flat. The thinner the leather, the better the French seam looks and the easier it is to sew.

On medium weight leather, a French seam is possible but harder. The fold is stiff, the seam is bulky, and pressing it flat is difficult. Skiving the allowance, thinning it with a knife before folding, helps, but the result is still bulkier than a plain seam. On thick leather, a French seam is not a good choice: the double fold is too thick to sew cleanly, and the finished seam stands up instead of lying flat.

A French seam also suits straight seams better than curved ones. A curve in leather is hard to fold neatly, and the enclosed allowance bunches on the inside of the curve. A straight seam on a bag, a jacket panel, or a lining is a good case for a French seam on leather. A curved seam is usually better sewn as a plain seam or a lapped seam.

Sewing a French seam on leather

  1. Test the seam on a scrap of the same leather, including the folding and the second pass, before sewing the item.
  2. Mark the seam line on both pieces, and hold them together with clips or double sided tape, wrong sides together for the first pass.
  3. Sew the first pass with a leather point needle, a strong thread, and a longer stitch length than cloth needs.
  4. Trim the allowance close to the stitching, leaving about 3 millimetres, and skive the trimmed allowance thin if the leather allows it.
  5. Fold the leather so the right sides are together, enclosing the trimmed allowance, and hold the fold with clips or tape.
  6. Sew the second pass along the folded edge, enclosing the first stitching completely, and tap the finished seam flat with a mallet.

Skiving the allowance

Skiving is the key step that makes a French seam work on leather. A skiving knife removes a thin layer from the underside of the seam allowance, tapering it toward the edge. The thinned allowance folds more easily, adds less bulk, and lets the finished seam sit flatter. Without skiving, a French seam on leather is often too thick to look neat.

Skiving takes practice. The knife should be sharp, the cut should be even, and the taper should be gradual. Test the skiving on a scrap first, and skive the allowance before the first pass is sewn, or between the two passes, whichever gives better control. A skived allowance that is too thin can tear, so the thinning should be gradual rather than aggressive.

If skiving is not practical, a thinner leather is the answer. Choosing a leather that suits a French seam is easier than forcing a thick leather into a seam it does not suit.

Finishing the seam

After the second pass, the French seam on leather is finished by tapping it flat with a mallet. A thin layer of leather glue can be applied inside the fold before the second pass, which holds the enclosed allowance in place and keeps the seam flat. An iron can be used on some leathers with a press cloth and a low heat setting, but heat can damage leather, so a mallet and glue are the safer choice.

The finished seam should be narrow, flat, and even, with no raw edge showing and no bulk standing up from the surface. If the seam is too bulky, the leather is too thick for a French seam, and a plain seam or a lapped seam would be a better choice for that item.

A French seam on leather is a specialist seam. It looks clean and it is strong, but it asks for thin leather, careful skiving, and a straight seam. On the right leather, it is one of the neatest seams available. On the wrong leather, it is a fight, and a plain seam will serve the item better.