The Seam Line How seams are made, finished, and fixed

Home / Leather Seams: How They Are Made

Leather Seams: How They Are Made

A leather seam is planned before it is sewn, because every needle hole stays visible. Leather cannot be unpicked and resewn without leaving marks, so the seam is tested on a scrap, then stitched once, with a longer stitch than cloth needs.

Why leather seams are different

On cloth, a seam can be unpicked and resewn. The needle holes close up, the fabric recovers, and the second attempt looks as good as the first. On leather, the needle cuts a hole in the material, and that hole stays. Unpicking a leather seam leaves a row of holes along the old stitching line, and those holes cannot be hidden. A leather seam has to be right the first time.

Leather is also thick and firm. It does not ease the way cloth does, it does not stretch around a curve, and it does not press flat with an iron in the same way. A seam on leather is a construction joint between two firm pieces, and it has to be strong enough to hold under stress without the help of easing or pressing.

Leather seams are used on jackets, bags, belts, shoes, and upholstery. In each case, the seam is part of the look of the item as well as part of its construction. The stitching on a leather jacket is visible and decorative, and the seam itself is a design line. That visibility means the stitching has to be even and the seam has to be neat.

The seams used on leather

The plain seam is the most common seam on leather. Two pieces are placed together, stitched, and the allowances are pressed open or to one side, then often glued down. The plain seam is simple and strong, and it suits most leather work. The allowances are usually skived, which means thinned with a knife, so they do not add too much bulk.

A lapped seam is used where a flat, strong join is needed. One piece overlaps the other, and the stitching goes through both layers. A lapped seam is flatter than a plain seam and very strong, which makes it useful on bags and belts. It is also easier to sew on thick leather, since the layers are not folded back on themselves.

A French seam is sometimes used on leather, but it is not the usual choice. A French seam encloses the raw edges, which is useful on a fabric that frays, but leather does not fray, and the double fold of a French seam adds bulk that is hard to press flat on leather. A French seam on leather is used mainly on thin, soft leather, or where the enclosed edge is wanted for the look.

A welt seam, where a strip of leather is inserted into the seam, is used on shoes and bags to add strength and a decorative line. A bound seam, where the raw edges are wrapped, is used where the edge needs protection. Each of these seams has its place, but the plain seam and the lapped seam cover most leather work.

Stitching leather

Stitch length on leather is kept longer than on cloth. A short stitch perforates the leather, like a row of holes in paper, and the seam can tear along the perforation. A longer stitch, with more leather between each hole, keeps the seam strong. The exact length depends on the thickness of the leather, but it is always longer than the stitch length used on a comparable cloth.

The needle for leather is a wedge shaped needle, sometimes called a leather point needle. It cuts a small slit in the leather rather than punching a round hole, and the slit closes around the thread. A round point needle, the kind used on cloth, pushes the leather aside and can leave a larger hole. The thread for leather is usually a strong polyester or nylon thread, thicker than the thread used on cloth, since the seam has to hold a firm material under stress.

A walking foot helps on leather, since it feeds the top layer at the same speed as the feed dogs feed the bottom layer. Without it, the top layer can stick to the presser foot and creep, leaving an uneven seam. A Teflon foot, or a roller foot, also helps, since leather can stick to a standard metal presser foot. A little talcum powder on the leather can reduce sticking too, though it should be brushed off afterwards.

Preparing the seam

Before sewing, the seam is marked on the leather with a scratch awl, a silver pen, or a piece of chalk. Ink can stain leather, so a marker made for leather, or a light scratch, is safer. The seam line should be marked clearly, since leather cannot be pinned the way cloth can: a pin leaves a hole, so pins are used sparingly, and only inside the seam allowance.

Clips, tape, or glue are used instead of pins to hold leather pieces together. Double sided tape made for leather holds the layers in place while they are sewn, and it can be left in the seam. A thin line of leather glue does the same job. Clips made for sewing, which grip the edge without piercing it, are useful on a straight seam.

Test the seam on a scrap of the same leather before sewing the item. Test the stitch length, the tension, and the foot, and check the result. The scrap test is more important on leather than on cloth, because a mistake on the item cannot be unpicked without leaving marks.

Finishing the seam

After sewing, the seam allowances on leather are usually glued down rather than pressed. A thin layer of leather glue holds the allowance flat, and the seam can be tapped with a mallet to set it. An iron can be used on some leathers with a press cloth and a low heat setting, but heat can damage leather, so glue and a mallet are the safer choice.

Skiving thins the seam allowance so it does not add bulk. A skiving knife removes a thin layer from the underside of the allowance, tapering it toward the edge. Skiving takes practice, and it should be tested on a scrap first, but it makes a visible difference to how flat a leather seam sits.

The finished seam should be strong, even, and flat, with no puckers and no wandering stitching. If a seam has to be removed, it should be cut out rather than unpicked, and the piece should be replaced if possible. A row of needle holes in leather is permanent, and the best repair is to avoid needing one.

Leather seams reward preparation. Mark the line, test on a scrap, hold the pieces without pins, and stitch once with a longer stitch, and the seam will be as strong and as neat as the leather deserves.