Leather Seam Allowance
A leather seam allowance is trimmed and thinned, not pressed open like a cloth allowance. The width depends on the seam and the thickness of the leather, and the allowance is usually glued down after sewing.
Why the allowance is different on leather
On cloth, the seam allowance is a working margin. It can be wide, it can be pressed open or to one side, and it can be trimmed after sewing. On leather, the allowance is a piece of firm material that adds bulk to the seam. A wide allowance on leather makes the seam thick and stiff, and it can show as a ridge on the outside of the item.
Leather also cannot be pressed the way cloth can. An iron can damage leather, and a thick allowance pressed flat with heat can leave a mark. The allowance on leather is managed by trimming and skiving, thinning it with a knife, rather than by pressing it.
The allowance also has to be planned, because a leather seam cannot be unpicked and resewn without leaving holes. If the allowance is too narrow, there is no room to adjust the seam. If it is too wide, it adds bulk. The width should be chosen before cutting, and it should be tested on a scrap.
Standard widths
A plain seam on leather usually uses an allowance of about 1 centimetre. That width gives enough leather to hold the stitching securely, without adding too much bulk. On a thin leather, a 1 centimetre allowance is easy to manage. On a thick leather, it may need skiving to sit flat.
A lapped seam uses a wider allowance on the overlapping piece, since the overlap is the seam. The under piece needs only a narrow allowance, while the top piece needs enough width to overlap and be stitched. The exact widths depend on the design, but the overlap is usually at least 1 centimetre so the stitching has enough leather to hold.
A French seam on leather starts with a narrow allowance, about 6 millimetres, for the first pass. The allowance is trimmed to about 3 millimetres before the second pass. A wider starting allowance would make the folded seam too bulky. The narrow width is part of what makes a French seam work on leather at all.
A bound seam or a welt seam needs an allowance wide enough to wrap the binding or the welt, usually about 1.5 centimetres. The extra width is the material that is folded around the edge, and it should be trimmed after the binding is attached so it does not add bulk.
Trimming the allowance
After sewing, the seam allowance on leather is usually trimmed to reduce bulk. The trimming should be even, and it should stop short of the stitching. A trimmed allowance of about 6 millimetres is a common finished width on a plain seam. On a thick leather, the allowance may be trimmed narrower, since the thickness itself adds bulk.
Trimming should be done with a sharp knife or sharp scissors. A dull blade drags the leather and leaves a ragged edge. Trim in short, even cuts, and check the width as you go. An uneven allowance will make the seam sit unevenly, and the ridge will show on the outside of the item.
On a curved seam, the allowance needs trimming and notching so it can lie flat around the curve. Small notches cut out of the allowance remove bulk on an inward curve. Small clips cut into the allowance let it spread on an outward curve. The cuts should stop just short of the stitching, never through it.
Skiving the allowance
Skiving thins the seam allowance by removing a thin layer from the underside, tapering it toward the edge. A skived allowance folds more easily, adds less bulk, and lets the seam sit flat. Skiving is used on plain seams, French seams, and bound seams, wherever the allowance needs to be thin.
A skiving knife should be sharp, and the cut should be even and gradual. The taper should run from full thickness at the stitching line to thin at the edge. A skived allowance that is too thin can tear, so the thinning should be gradual. Test the skiving on a scrap of the same leather first, and practise the knife angle before skiving the item.
Skiving is not needed on every leather seam. On a thin leather, the allowance is already thin enough, and skiving adds risk without much benefit. On a thick leather, skiving makes a visible difference. The decision depends on the leather and the seam, and a scrap test will show whether it is needed.
Finishing the allowance
After trimming and skiving, the allowance on leather is usually glued down. A thin layer of leather glue holds the allowance flat against the item, and the seam is tapped with a mallet to set it. The glue should be applied thinly and evenly, since too much glue can seep out and mark the leather.
An iron can be used on some leathers with a press cloth and a low heat setting, but heat can damage leather, so glue and a mallet are the safer choice. The finished allowance should be flat, with no ridge and no bulk showing on the outside of the item.
If the allowance shows as a ridge on the outside, it is too wide or too thick. Trimming it narrower, or skiving it thinner, will fix the problem. A ridge that remains after trimming and skiving usually means the leather is too thick for that seam, and a different seam should be used.
On leather, the allowance is part of the seam, not a leftover. Trim it, thin it, glue it flat, and the seam will sit as neatly as the leather allows.