How to Sew Leather Seams
Sewing a leather seam is a matter of preparation. Mark the line, test the settings on a scrap, hold the pieces together without pins, and stitch slowly. The seam is sewn once, because unpicking leaves holes.
What you need
A leather point needle is the first requirement. It has a wedge shaped tip that cuts a small slit in the leather, and the slit closes around the thread. A round point needle, the kind used on cloth, pushes the leather aside and leaves a larger hole. Use a needle size suited to the thickness of the leather: a heavier leather needs a larger needle, and a lighter leather needs a smaller one.
Thread for leather is stronger and thicker than thread for cloth. A bonded polyester or nylon thread is the usual choice, since it is strong, smooth, and resistant to wear. The thread should be matched to the leather in colour, since the stitching on leather is visible and decorative as well as structural.
A walking foot, a Teflon foot, or a roller foot makes sewing leather much easier. Leather can stick to a standard metal presser foot, which causes the top layer to creep and the seam to go uneven. A Teflon foot slides over the leather, a roller foot rolls over it, and a walking foot feeds both layers together. Any of the three is better than a standard foot on leather.
Marking and holding the pieces
Mark the seam line on the leather with a scratch awl, a silver pen, or tailor's chalk. Ink can stain leather, so avoid ordinary pens. A light scratch with an awl marks the line without leaving a visible mark on the finished item, since the scratch sits inside the seam allowance. Mark both pieces, and mark the matching points where the pieces should line up.
Do not pin leather the way cloth is pinned. A pin leaves a hole, and a hole in leather is permanent. Use clips, double sided tape, or glue instead. Sewing clips grip the edge of the leather without piercing it, and they are useful on a straight seam. Double sided tape made for leather holds the layers together while they are sewn, and it can be left inside the seam. A thin line of leather glue does the same job.
Place the holding method inside the seam allowance, so it does not show on the finished item. On a curved seam, use more clips or a longer line of tape, since the curve needs more holding than a straight seam. Check that the pieces are aligned before sewing, since they cannot be shifted easily once the stitching starts.
Testing on a scrap
Before sewing the item, test the seam on a scrap of the same leather. Sew a short seam with the same needle, thread, stitch length, and foot that will be used on the item, and check the result. The stitching should be even, the layers should not shift, and the leather should not be perforated.
Stitch length is the main thing to test. A stitch that is too short perforates the leather and weakens the seam. A stitch that is too long looks loose and may not hold under stress. The right length is longer than the length used on cloth, and it depends on the thickness of the leather. Test a few lengths on the scrap and choose the one that looks even and holds firmly.
Test the tension too. If the tension is too tight, the thread will pull the leather together and pucker the seam. If it is too loose, the stitching will loop on the surface. Adjust the tension a little at a time, testing after each change, until the stitching lies flat on both sides.
Sewing the seam
- Set the machine with a leather point needle, a strong thread, and a walking foot, Teflon foot, or roller foot.
- Mark the seam line on both pieces, and hold them together with clips, tape, or glue, right sides together for a plain seam.
- Sew slowly, guiding the leather without pulling it. Let the feed dogs move the leather, and keep the seam allowance even.
- Do not backstitch at the start or end of the seam. Backstitching perforates the leather and weakens it. Leave long thread tails instead, and knot them by hand or tuck them inside the seam.
- Check the seam from both sides. The stitching should be even, the layers should be aligned, and the leather should lie flat.
- Finish the seam allowance by gluing it down and tapping it with a mallet, or by skiving it thin before gluing.
Finishing and pressing
After sewing, the seam allowance on leather is usually glued down rather than pressed. Apply a thin layer of leather glue to the allowance, press it flat, and tap it with a mallet to set it. The mallet flattens the seam without the heat of an iron, and the glue holds it in place.
An iron can be used on some leathers, with a press cloth and a low heat setting, but heat can damage leather, so it should be tested on a scrap first. Glue and a mallet are the safer choice, and they work on every kind of leather. The finished seam should be flat, with no bulk and no ridge.
Skiving thins the allowance before it is glued down. A skiving knife removes a thin layer from the underside of the allowance, tapering it toward the edge. Skiving takes practice, and it should be tested on a scrap first, but it makes a leather seam sit much flatter, especially on a thick leather.
Never backstitch on leather. The extra holes weaken the seam and show on the finished item. Leave long thread tails and finish them by hand instead.
If a seam goes wrong
A seam sewn in the wrong place cannot simply be unpicked on leather. Unpicking leaves a row of holes along the old stitching line, and those holes are permanent. If the seam is only slightly off, it may be possible to sew a second seam beside the first, but the first row of holes will still show.
The best response to a wrong seam is to cut the piece out and replace it, if there is enough leather. If the piece cannot be replaced, the holes can sometimes be disguised by placing a decorative stitch, a rivet, or a patch over them, but that changes the design. Prevention, by testing on a scrap and marking carefully, is worth far more than any repair.
Slow down, test first, and stitch once. Those habits are what make a leather seam strong and neat, and they are the difference between a seam that lasts and one that has to be hidden.