The Seam Line How seams are made, finished, and fixed

Home / Curved Seam on a Sleeve

Curved Seam on a Sleeve

A sleeve has two curved seams that matter: the cap easing into the armhole, and the long underarm seam that curves from the cuff to the body.

The two curves of a sleeve

A set in sleeve has two curved seams, and each one behaves differently. The sleeve cap, the curved top of the sleeve, is eased into the armhole, which is a slightly shorter curve. The extra length of the cap has to be distributed evenly, so the sleeve sits smoothly over the shoulder without gathers showing. The underarm seam, which runs from the cuff up to the armpit and then into the side seam, is a long curve that changes direction at the underarm, and it has to lie flat where the arm moves.

The cap is the harder of the two, because easing is involved. The underarm seam is the longer of the two, because it runs the full length of the sleeve and the body. Both need the standard curved seam techniques: staystitching, careful pinning, slow stitching, clipping or notching, and pressing over a curved surface. Getting both right is what makes a sleeve look set in properly rather than sewn on.

The shape of the sleeve matters too. A fitted sleeve has a higher cap and a tighter curve than a loose sleeve, so it needs more easing and more care. A loose sleeve, such as a dolman or a dropped shoulder, has a gentler curve and is more forgiving. The pattern tells the story: a tall, narrow cap means a fitted sleeve and a demanding seam, while a low, wide cap means an easier one.

Setting in the sleeve cap

Start by staystitching the cap, just inside the seam line, to stop the curve stretching while it is handled. Then run two rows of easing stitches along the cap, between the pattern notches, just inside the seam line. These are long, loose stitches that can be pulled up to gather the cap very slightly. The easing should be spread evenly across the top of the cap, with none of it concentrated at the front or the back.

Pin the sleeve into the armhole, matching the pattern notches first: the top of the cap to the shoulder seam, the front notch to the front of the armhole, and the back notch to the back. Then pin between the notches, distributing the easing evenly. The pins should be at right angles to the stitching line, and close enough together that the layers cannot shift while stitching.

Stitch the seam with the sleeve side on top, so the easing can be watched as it goes under the foot. Stitch slowly, and stop with the needle down to reposition the fabric when the curve turns. The stitching should follow the seam line exactly, because a sleeve cap that is stitched off line will sit crookedly on the shoulder, and the error shows from the outside.

The underarm seam

The underarm seam is usually sewn as one continuous seam from the cuff to the hem, joining the sleeve and the side of the body in a single pass. This gives a clean line and avoids a join at the armpit, which is a point of strain. The seam curves at the underarm, where the sleeve meets the body, and that curve needs clipping or notching so it lies flat.

Pin the seam from the cuff upward, matching the underarm point first, then working toward the hem and toward the cuff. The underarm point is where the sleeve and the body meet, and it is the point where a mismatch shows most, so it should be pinned exactly. If the sleeve and the body are different lengths at the underarm, the extra length should be eased evenly, not bunched at the point.

Stitch the seam slowly through the curve at the underarm, stopping with the needle down to reposition the fabric. After stitching, clip the outward curve or notch the inward curve at the underarm, so the allowance can follow the turn. Then press the seam open or to one side, over a sleeve roll, so the curve keeps its shape. A sleeve roll is a long, narrow pressing cushion that fits inside a sleeve, and it is the right tool for this seam.

Pressing and checking the sleeve

Press the cap seam over a tailor's ham, which supports the curve of the shoulder. Press the underarm seam over a sleeve roll, which fits inside the sleeve tube. Pressing either seam flat on the board distorts the curve and can leave the sleeve sitting wrong. Let each seam cool in shape before moving it, because a warm seam can be pulled out of shape while it is still soft.

Check the sleeve from the outside. The cap should sit smoothly over the shoulder, with no puckering along the armhole and no gathers showing. The underarm seam should lie flat, with no pulling at the armpit and no ridge showing through. Turn the sleeve inside out and check the seams there too. The allowances should lie flat, with no bunching at the curve, and the clipping or notching should have done its job.

If the cap puckers, the easing was probably uneven, or the cap was stretched while pinning. The fix is to unpick the cap seam, re ease the cap, and restitch it. If the underarm seam pulls, the allowance probably needs more clipping, or the seam was stitched off line at the curve. Both are small repairs, and both are worth doing, because a sleeve that is set in badly shows every time the garment is worn.

Try the garment on before finishing the sleeve hems. A sleeve that looks right on the table can sit differently on the body, and the fitting check catches a cap that needs re easing while it is still easy to fix.