Zigzag Seam Finish
A zigzag finish is the simplest way to stop a seam edge fraying on a standard machine. It wraps the edge in a zigzag stitch, and it needs no extra equipment.
How a zigzag finish works
After the seam is sewn, the machine is set to a zigzag stitch, and the stitch is run along each raw edge. The needle swings from side to side, and on one side it falls just off the edge of the fabric, so the thread loops around the edge and holds the cut fibres in place. The result is an edge that frays much less in wear and in the wash, and a seam allowance that stays tidy. The zigzag does not enclose the edge, and it does not trim it, so the edge is still visible, wrapped in thread, on the wrong side of the garment. That is enough for most everyday garments, especially those that will be lined or where the seams are hidden. The finish is quick, it uses the same thread as the seam, and it can be done on any machine with a zigzag stitch, which covers almost every domestic machine.
Choosing the stitch width and length
Stitch width and length should suit the fabric. A wider zigzag wraps more of the edge and holds a fabric that frays heavily, while a narrower zigzag is enough on a stable cotton and looks tidier. A shorter stitch length gives a denser wrap, which holds better, but it can pucker a light fabric if it is too short. A longer stitch length is faster and lies flatter, but it may not hold a loosely woven fabric. The usual approach is a medium width and a medium length, tested on a scrap of the same fabric. Sew the zigzag along the scrap edge, pull at the edge, and see whether threads still come away. If they do, widen the stitch or shorten the length. If the edge puckers, narrow the stitch or lengthen it. The test takes a minute, and it avoids finishing a whole garment with a stitch that does not hold.
How to sew the finish
- Sew the plain seam first, and press it as the pattern asks, either open or to one side, before finishing the edges.
- Set the machine to a zigzag stitch, choosing a width and length tested on a scrap of the same fabric.
- Place the seam allowance under the foot with the raw edge lined up so the needle falls just off the edge on the outer swing.
- Sew slowly along the edge, keeping the edge in the same position, and let the feed dogs move the fabric rather than pulling it.
- Finish the second allowance in the same way, then press the seam again and check that the thread wraps the edge fully along the whole length.
Which fabrics suit a zigzag finish
A zigzag finish suits medium-weight wovens, such as cotton, linen and stable rayons, where it holds the edge well and does not add bulk. It suits knits too, since the zigzag stretches a little, though overlocking stretches better and is preferred for a knit that is pulled hard. It is less suited to sheer fabrics, where the zigzag thread shows through and looks rough, and to very heavy fabrics, where the stitch may not wrap the thick edge cleanly. On a fabric that frays heavily, a zigzag may need to be combined with a second pass, or replaced by overlocking or binding, since a single zigzag may not hold all the threads. On a fabric that frays only a little, a zigzag is often more than enough, and a pinked edge may be quicker still. The finish is a practical compromise: not as tidy as overlocking, not as smart as binding, but quick, secure and available on any machine.
Common mistakes
The most common mistake is sewing the zigzag too far from the edge, so the needle never falls off the fabric and the thread does not wrap the edge at all. The stitch then sits on top of the allowance and does nothing to stop fraying. Line the edge up carefully, and check the first few stitches before continuing. Another mistake is using a stitch that is too wide for a light fabric, which puckers the edge and makes the seam pull. Test on scrap and narrow the stitch if the edge waves. A third mistake is finishing the edges before pressing the seam, which makes it harder to press the seam flat afterwards. Press first, finish second, then press again lightly. If the zigzag thread breaks, check the tension and the needle, since a blunt needle can snag the thread on a thick edge.
A zigzag finish can also be used on a hem edge or on a facing edge, not only on a seam allowance. The same method applies: set a medium zigzag, line the edge up so the needle falls just off it, and sew slowly. On a curved edge, the fabric should be eased around the curve rather than pulled, since pulling will distort the edge and the zigzag will pucker. On a straight edge, a seam guide helps to keep the stitching even. The finish is useful on a garment where a hem or a facing would otherwise fray, and it is quicker than binding the edge. Test the stitch on a scrap of the same fabric, especially on a curve, before finishing the garment edge, since a curve shows a mistake more clearly than a straight seam.
A zigzag finish will not win a prize for looks, but it does the job on most everyday garments. Test the width on scrap, keep the needle just off the edge, and press the seam after finishing, and the edges will stay tidy.