The Seam Line How seams are made, finished, and fixed

Home / Seam Finishes Without a Serger

Seam Finishes Without a Serger

A serger makes finishing fast, but it is not essential. A standard sewing machine, a pair of pinking shears and an iron can produce seam finishes that are tidy, durable and smart.

Zigzag stitching

The zigzag stitch is the most useful finish without a serger. After sewing the seam, set the machine to a medium-width zigzag and stitch along each raw edge, with the needle falling just off the edge on one side so the thread wraps around it. The zigzag holds the threads of the fabric in place and stops them fraying. It works on most medium-weight fabrics, and it is quick, since each edge takes only one pass. The stitch width and length should suit the fabric: a wider zigzag on a fabric that frays heavily, a narrower one on a stable cotton. The finish is not as tidy as overlocking, and the edge still shows the zigzag thread, but it is secure and it needs no extra equipment. On a garment that will be lined, or on seams that are hidden, a zigzag finish is often all that is needed. Test the width on a scrap, since a zigzag that is too narrow may not catch the edge, and one that is too wide may pucker it.

French and mock French seams

A French seam encloses the raw edges completely, and it needs no serger at all. It is sewn in two passes: first with the wrong sides together and a narrow allowance, then with the right sides together, enclosing the first seam inside the second. The result is a clean, enclosed seam that suits sheer and lightweight fabrics. A mock French seam is a simpler version: sew a plain seam, press it open, then fold each allowance under and stitch it down, so the raw edges are tucked away. It is not as neat as a true French seam, but it is easier on a curved seam and it works on a wider range of fabrics. Both finishes take longer than a zigzag, but they give a finish that looks good from the inside, which matters on an unlined garment. They are also durable, since the edges are enclosed rather than merely wrapped.

Bound and turned finishes

Binding covers the raw edge with a strip of bias binding, folded over the edge and stitched down. It looks smart, it suits jackets and unlined garments, and it needs only a standard machine. Ready-made bias binding works well, and binding cut from the garment fabric gives a matched finish. The binding should be pinned or clipped in place and stitched close to its folded edge, so it does not slip. A turned and stitched finish is simpler: fold the raw edge under by a small amount, press it, and stitch close to the fold. It is tidy, it needs no extra material, and it works on stable fabrics that press well. It is less suited to fabrics that fray heavily, since the fold may not hold the loosest threads, and it adds a little bulk. Both finishes are slower than a zigzag, but they give a more finished look, and they are worth the time on a garment that will be seen from the inside.

Pinking and other simple finishes

Pinking shears cut a zigzag edge that frays less than a straight cut, because the threads are cut at an angle and have less length to unravel. Pinking is the quickest finish of all: trim the allowance with the shears and the seam is done. It suits fabrics that fray only a little, such as a stable cotton or a light wool, and it is often used on seams that will be hidden by a lining. It is not enough on a fabric that frays heavily, and it does not look smart on a visible seam. Another simple finish is to stitch a straight line close to the raw edge, which holds the threads in place, though it does not wrap the edge. A narrow hem stitch or a hand overcast stitch can also finish an edge, and hand finishing is sometimes chosen for a delicate fabric that a machine stitch would damage. These simple finishes are useful when time is short, or when the seam is in a place that will not be seen.

A finish that looks tidy on the table may still fray in the wash. Test the chosen finish on a scrap, wash the scrap if possible, and check the edge before finishing the garment seams.

Choosing between them

Choose a zigzag for speed and for most everyday garments. Choose a French seam for sheer and lightweight fabrics, and a mock French seam where a curve makes a true French seam difficult. Choose binding for an unlined jacket or a garment where the inside will be seen. Choose a turned and stitched finish for a stable fabric where a tidy edge is wanted without extra material. Choose pinking for a quick finish on a fabric that frays only a little, or on a seam hidden by a lining. The equipment is the same in every case: a standard machine, an iron and sharp tools. The difference is time and appearance, and the right choice is the one that suits the fabric, the garment and the time available.

Many sewists work without a serger for years and produce garments with tidy insides, because the finishes that need no serger are also the finishes that look the smartest. Binding, French seams and turned finishes were the standard before sergers were common, and they are still used on tailored garments where the inside is meant to be seen. The absence of a serger is therefore not a limitation on quality, only on speed. A garment finished by hand methods may take longer, but it will often look better inside than a garment finished quickly on a serger. That trade is worth keeping in mind when deciding whether a serger is needed: it saves time, but it does not improve the look of the inside, and for many garments the slower finishes are the better choice.

Without a serger, the choice is wider than it first seems. Zigzag for speed, French for sheers, binding for jackets, and pinking for a quick finish all give a tidy inside without extra equipment.