Bound Seam Finish
A bound finish covers the raw edge of a seam with a strip of bias binding. It looks smart, it feels smooth, and it suits garments where the inside will be seen.
What a bound finish looks like
On the wrong side of the garment, a bound seam shows a neat strip of fabric folded over each raw edge, stitched down close to its fold. The binding covers the cut fibres completely, so they cannot fray, and the edge feels smooth to the touch. On the right side, only the plain seam stitching shows, so the finish does not change the look of the garment from the outside. The binding can match the garment fabric, which gives a quiet, tailored look, or it can contrast, which turns the inside into a design feature. Ready-made bias binding is often used, in cotton or in a soft synthetic, and binding cut from the garment fabric gives the most closely matched result. The width of the binding decides how much of the allowance it covers, and a binding that is too narrow may not cover the edge fully, while one that is too wide adds bulk.
When binding is the right choice
Binding is the usual choice for an unlined jacket, a coat or a waistcoat, where the seams are visible every time the garment is opened or taken off. It is also used on bags, where the inside is seen, and on garments in fabrics that fray heavily, since the binding holds the edge more securely than a zigzag. It suits medium-weight wovens, such as wool, linen and cotton, which press well and hold the binding in place. It is less suited to very sheer fabrics, where the binding shows through, and to very thick fabrics, where the extra layers make the seam bulky. It is also slower than overlocking or zigzag, so it is chosen when the garment deserves the time, rather than for every seam on an everyday garment. A bound finish raises the standard of the inside, and it is a sign of a well made garment.
How to bind a seam edge
- Sew the plain seam first, and press it as the pattern asks, either open or to one side, before binding the edges.
- Cut or choose bias binding wide enough to fold over the raw edge and cover it, with a little to spare on the underside.
- Open one fold of the binding, pin it to the raw edge with right sides together, and stitch along the fold line, keeping the stitching straight and even.
- Fold the binding over the raw edge to the other side, so it covers the edge completely, and pin or clip it in place.
- Stitch close to the folded edge of the binding, through all layers, using a stitch length suited to the fabric, and press the finished edge flat.
- Repeat for the second allowance, then press the seam again and check that no raw edge shows from either side.
Binding a seam pressed to one side
When the seam allowances are pressed to one side, both edges can be bound together in one strip, which is quicker and gives a single neat edge. The binding is folded over both allowances at once, and stitched down in the same way. This method suits a jacket lining or a seam where the allowances are pressed together for strength. When the allowances are pressed open, each edge is bound separately, which is tidier on a garment where the seam needs to lie flat. The choice depends on the pattern and on how the seam should sit. Either way, the binding should be pinned before stitching, since a strip that shifts will cover the edge unevenly. At a curve, the bias cut of the binding helps it to bend around the edge without puckering, which is why bias binding is used rather than a straight strip.
Problems to watch
The most common problem is binding that slips while it is stitched, leaving part of the raw edge exposed. Pin or clip closely, and stitch slowly, to keep it in place. Another problem is binding that is too narrow for the allowance, so the edge peeks out on the underside. Choose a wider binding, or trim the allowance narrower before binding. If the binding puckers, the stitch may be too tight, or the binding may have been pulled while sewing, so test the tension on a scrap. If the bound edge feels stiff, the binding fabric may be too heavy for the garment fabric, and a lighter binding should be used. A bound finish takes patience, but the result is a seam that looks finished and feels smooth, and that will not fray.
Binding can be cut from the garment fabric, from a contrasting fabric, or bought ready-made. Cutting it from the garment fabric gives the closest match, and it is worth doing when the fabric is available and the garment deserves a matched inside. Ready-made binding is quicker, and it comes in a wide range of colours, though the colour may not match the fabric exactly. A contrasting binding can be a design choice, turning the inside of the garment into a feature, and it is often used on jackets and bags where the inside is seen. Whichever binding is used, it should be cut on the bias, so it bends around curves, and it should be pressed before it is pinned, so the folds are crisp. Test the binding on a scrap first, to check the width, the colour and how it handles.
Binding takes longer than a zigzag or an overlock, but on an unlined jacket it is the finish that shows the garment was made with care. Choose a binding that suits the fabric, pin it well, and stitch close to the fold.