The Seam Line How seams are made, finished, and fixed

Home / Turned and Stitched Seam Finish

Turned and Stitched Seam Finish

A turned and stitched finish folds the raw edge of a seam allowance under and stitches it down. It is tidy, it needs no serger, and it works on stable fabrics.

What the finish looks like

On the wrong side, a turned and stitched seam shows each allowance with its raw edge folded under and held down by a row of stitching close to the fold. The edge is enclosed by the fold, so it cannot fray, and the seam allowance lies flat. On the right side, only the plain seam stitching shows, unless the turned stitching is done through all layers, in which case a row of stitching may show on the right side too. The usual method stitches only through the allowance, so the right side stays clean. The finish looks neater than a zigzag or a pinked edge, and it feels smooth, since there are no thread loops to catch. It adds a little bulk, because the edge is folded, but on a medium-weight fabric that bulk is small and the seam still presses flat. The finish is a good middle ground: tidier than a quick finish, simpler than binding, and durable enough for most everyday garments.

When to use it

A turned and stitched finish suits stable wovens, such as cotton, linen and light wool, which fold and press well. It suits garments where the seams are visible from the inside, such as an unlined skirt or a simple top, since it looks tidy. It suits a sewist without a serger, since it needs only a standard machine and an iron. It is less suited to fabrics that fray heavily, since the fold may not hold the loosest threads, and a zigzag or overlocking may be needed as well. It is less suited to very thick fabrics, where the fold adds bulk and is hard to stitch through, and to very sheer fabrics, where the fold shows through. It is also less suited to knits, since the fold does not stretch well and the stitching may snap. For a medium-weight woven garment, where a tidy inside is wanted without the time of binding, a turned and stitched finish is a sound choice.

How to sew the finish

  1. Sew the plain seam first, and press the allowances open or to one side, as the pattern asks, before turning the edges.
  2. Fold the raw edge of one allowance under by a small amount, about the width of a narrow fold, and press the fold flat along the whole length.
  3. Stitch close to the folded edge, through the allowance only, keeping the stitching straight and even, and taking care not to catch the garment fabric underneath.
  4. Repeat for the second allowance, then press the seam again from the wrong side and from the right side, and check that no raw edge shows.

Keeping the fold even

An even fold is what makes this finish look neat. Fold a small amount at a time, press as you go, and pin or clip the fold in place before stitching, especially on a long seam. A seam gauge helps to keep the fold the same width along the whole length. If the fold is too narrow, the raw edge may peek out; if it is too wide, the seam becomes bulky. Pressing is important: a fold that is pressed flat stays in place while it is stitched, while a fold that is only finger-pressed can shift under the foot. On a slippery fabric, pins placed close together help, and on a thick fabric, a longer stitch and a slightly wider fold may be needed. Check the fold from the right side before stitching, since a fold that looks even from the wrong side can still wander. The stitching should run close to the folded edge, so it catches the fold fully along its length.

Stitch through the allowance only, not through the garment, unless the pattern asks for topstitching on the right side. Catching the garment by mistake leaves a row of stitching on the outside that is hard to remove cleanly.

Turned and stitched compared with binding

Binding and turning both fold the edge under, but binding covers the edge with a separate strip, while turning folds the allowance itself. Binding looks smarter and suits a jacket, while turning is quicker and suits an everyday garment. Binding holds a fraying edge more securely, since the strip covers it completely, while turning relies on the fold alone. Turning adds less bulk than binding, since there is no extra strip, and it needs no extra material. The choice depends on the garment: binding for a jacket where the inside should look tailored, turning for a top or a skirt where a tidy edge is enough. Both finishes need careful pressing, and both look better than a zigzag, though both take longer. For a garment that will be lined, neither is needed, and a quicker finish is enough.

A turned and stitched finish can be used on a pocket edge, a facing edge or a hem, as well as on a seam allowance. The method is the same: fold the raw edge under, press it, and stitch close to the fold. On a pocket, the turned edge gives a tidy finish that will not fray when the pocket is used, and on a facing it gives a clean edge that sits flat against the garment. The fold should be even, and the stitching should be close to the fold, so the edge is fully caught. On a curved edge, the fold should be clipped or notched before it is pressed, so it lies flat without puckering. The finish is versatile, and once it is learned on a seam, it can be used in several other places on a garment.

A turned and stitched finish gives a tidy inside with only a machine and an iron. Fold evenly, press well, stitch close to the fold, and check that no raw edge shows before pressing the seam for the last time.