Overlocked Seam Finish
An overlocked finish wraps the raw edge of a seam in loops of thread. It is fast, it stops fraying, and it is the standard finish on most ready-made garments.
What overlocking does
An overlocker, also called a serger, is a machine that trims the fabric edge and wraps it in thread in one pass. It uses several threads, usually three or four, which loop around the edge and lock together, forming a neat, flexible wrap. The edge cannot fray, because the threads hold the cut fibres in place, and the seam allowance stays tidy even after many washes. Overlocking can be used to finish the edges of a plain seam after it is sewn, or the serger can sew and finish a seam in one pass, which is how many production garments are made. The finish is visible on the wrong side of the garment, as a row of thread loops along the edge, and it is usually pressed to one side or pressed open, depending on the garment. On the right side, only the plain seam stitching shows, so the finish does not change the look of the garment from the outside.
When overlocking is the right choice
Overlocking suits most fabrics, including wovens that fray heavily, knits that need a stretchy finish, and medium-weight cloths of all kinds. It is the fastest way to finish a seam, which makes it useful for garments with many seams, or for production sewing where time matters. It is also useful on a fabric that frays badly, since the thread wrapping holds the edge more securely than a zigzag. On knits, the overlock stitch stretches with the fabric, so the seam does not snap when the garment is pulled on. On a garment that will be washed often, overlocking holds up well, and the edge stays tidy. It is less suited to sheer fabrics, where the thread loops show through, and to very thick fabrics, where the serger may struggle with the layers. It is also less suited to a garment where the inside must look especially smart, such as an unlined jacket, where binding gives a cleaner look.
Overlocking on a standard machine
Without a serger, a standard sewing machine can give a similar finish with an overlock stitch or a zigzag stitch. The overlock stitch on a domestic machine wraps the edge in a similar way, though it is slower and the result is less tidy than a true serger finish. A zigzag stitch, sewn along the edge with the needle falling just off the edge, also wraps the threads and stops fraying. An overlock foot, which guides the fabric edge and keeps the stitch in place, helps to make the finish neater on a standard machine. The machine version is useful for a sewist who sews occasionally, or for a garment with only a few seams to finish. For frequent sewing, or for knits, a serger is worth considering, since it finishes faster and the stitch stretches better. Either way, the principle is the same: wrap the edge in thread so it cannot fray.
How to finish a seam by overlocking
- Sew the plain seam first, using a straight stitch or a stretch stitch suited to the fabric, and press the seam as the pattern asks.
- Set the overlocker for the fabric, checking the thread tension and the stitch width on a scrap, and test that the edge is trimmed cleanly without cutting into the seam.
- Feed each seam allowance through the overlocker separately, or together if the pattern asks for it, keeping the edge against the guide so the thread wraps it evenly.
- Press the finished seam, either open or to one side, and check that the thread loops cover the edge fully and that no raw fibres show.
- Trim any thread tails at the start and end of the seam, and secure them by stitching back a short distance or by threading the tail under the loops.
Problems and limits
The most common problem is the serger trimming too much, which narrows the allowance and can cut into the seam stitching. That is fixed by adjusting the cutting width and testing on scrap before overlocking the garment. Uneven tension shows as loops that are too loose or too tight, and the tension dials should be adjusted one at a time, testing after each change. On a very light fabric, the overlocking can pucker the edge, so a narrower stitch and a lighter tension help. On a very thick fabric, the serger may skip stitches or struggle to trim, and a zigzag on a standard machine may be easier. An overlocked edge is not as smart as a bound edge, and it is not as enclosed as a French seam, so it is a practical finish rather than a decorative one. For most garments, that practicality is exactly what is needed.
Thread choice on a serger matters more than on a standard machine, because the serger uses three or four threads at once, and the colour and the weight of each thread affect the look of the finished edge. Matching thread gives a tidy edge that blends with the fabric, while a contrasting thread makes the overlocking stand out, which is sometimes wanted as a design feature on a casual garment. A fine thread suits a light fabric, while a heavier thread suits a thick fabric, and the tension should be tested on scrap after any thread change. Keep a small stock of neutral colours, such as white, black, grey and beige, since those cover most fabrics, and test a coloured thread on scrap before overlocking a whole garment. The right thread makes the difference between an edge that looks neat and one that looks rough.
Overlocking is the workhorse of seam finishes: fast, secure and suited to most fabrics. Set the machine on scrap, keep the edge against the guide, and press the finished seam, and the inside of the garment will stay tidy through many washes.