Seam Allowance Pressing
Pressing is what turns a stitched seam into a flat, tidy one. How the allowance is pressed decides much of the result.
Press first, then decide
Seam allowance is the fabric between the stitching line and the raw edge, and pressing sets it in place. The first press after stitching should be a flat press along the stitching line, with the seam as sewn, before the allowance is pushed open or to one side. This is sometimes called setting the seam. It settles the stitches into the fabric and makes the next press easier.
Pressing is not ironing. Ironing slides the iron back and forth, which can stretch a seam out of shape. Pressing lifts the iron, places it down, holds it briefly, and lifts it again. The weight and the heat do the work, and the fabric stays where it was put. A little steam helps on fabrics that take it, but the iron should not be dragged across a fresh seam.
A pressing cloth protects fabrics that mark easily or shine under heat. A thin cotton cloth between the iron and the work is enough. It also protects the iron from any finish on the fabric.
Pressing open
Pressing open means opening the allowance so each side lies flat against the fabric on its own side of the stitching line. The seam then has one layer of allowance on each side, which spreads the bulk evenly. This is the usual choice for straight seams on medium weight woven fabric, and it gives the flattest result on the right side.
To press a seam open, open the pieces, lay the seam over a pressing surface with the allowance spread, and press from the wrong side first. A seam roll, which is a narrow padded roll, supports the seam so the allowance edges do not leave marks on the right side. Without that support, the edges of a wide allowance can press a ridge into the fabric that shows from the front.
Pressed open seams suit garments where the inside may be seen, such as an unlined jacket, because each allowance lies flat and looks tidy. They also suit seams that will be topstitched from the right side, since the stitching line is easy to follow when the seam lies flat.
Pressing to one side
Pressing to one side means folding both layers of allowance together toward one piece of fabric. This is the usual choice for quilt blocks, where all the allowances in a row are pressed in the same direction so the joins nest together when rows are sewn. It is also the choice for seams that will be enclosed, graded, or topstitched down, and for curved seams where opening the allowance would fight the curve.
Which side to press toward depends on the project. In quilting, the usual rule is to press toward the darker fabric, so the allowance does not show through the lighter one. In garments, the allowance is often pressed toward the back, toward the lining, or toward the side that gives the flattest result. The pattern instructions sometimes state a direction, and when they do, that direction is the one to follow.
Pressing to one side leaves two layers of allowance on one side of the stitching line and none on the other. On thick fabric that can create a visible ridge, so grading helps: the layer closest to the stitching line is trimmed slightly narrower than the layer above it, which steps the bulk down instead of leaving a sharp edge.
Grading, clipping, and notching
Grading means trimming the layers of an allowance to different widths so the bulk steps down gradually. It is used on enclosed seams, facings, and collars, where several layers meet and a single thick edge would show. The layer nearest the outside is left widest, and each layer underneath is trimmed a little narrower.
Clipping and notching deal with curves. On an outward curve, small snips are cut into the allowance so it can spread when pressed. On an inward curve, small wedges are cut out of the allowance so it can fold without bunching. Both cuts stop short of the stitching line. Cutting a stitch weakens the seam, so the cuts are kept a short distance from the line, and a narrow allowance on a tight curve may need several small cuts rather than a few deep ones.
Trimming the allowance itself is sometimes needed before pressing. A wide allowance on a curved seam resists pressing, and trimming it to about 1/4 inch after stitching makes the curve lie flat. The trim happens after stitching, never before, so the full allowance is there while the seam is sewn.
Tools that make pressing easier
A tailor ham, which is a firmly stuffed curved cushion, supports curved seams such as a sleeve cap or a bust curve while they are pressed. A sleeve roll or seam roll supports narrow seams and keeps allowance edges from marking the right side. A point presser, a narrow wooden tool with a pointed end, helps press corners and points from the inside.
A clapper, a flat block of hardwood, is pressed down on a seam after the iron is lifted. It holds the heat and the pressure in place while the fabric cools, which sets a sharp crease on fabrics such as wool. It is not needed for every project, but it is useful where a crisp seam matters.
None of these tools is required to press a seam well. A firm ironing surface, a pressing cloth, and a patient lift and place motion cover most work. The tools help with curves and bulk, and they are worth adding when those shapes appear often.
Allowance pressing is a small part of a project in time, and a large part of it in appearance. Set the seam flat first, choose open or to one side for a reason rather than by habit, and let the iron do the work without sliding. A seam pressed with care looks finished before any topstitching goes on, and it stays flat through wearing and washing far better than one that was rushed.