The Seam Line How seams are made, finished, and fixed

Home / ISO 4916 Bound Seams (Class 3)

ISO 4916 Bound Seams (Class 3)

Bound seams are ISO 4916 Class 3. In this construction a strip of fabric, called binding, wraps around the edge of the seam and is stitched in place, enclosing the raw edges inside the binding.

How a bound seam is built

The construction starts with a seam that has already been sewn, usually a superimposed seam with its allowances pressed open or to one side. A strip of binding fabric is then placed over the raw edge, folded around it so that it covers the edge on both sides, and stitched in place. The binding can be a straight strip cut on the grain, or a bias strip cut diagonally across the grain, which curves more easily around a shaped edge. The stitching passes through the binding and the seam allowances, holding the binding firmly over the edge.

The binding can be applied in one step or two. In a one-step method, the binding is folded around the edge and stitched through all layers at once. In a two-step method, the binding is first stitched to one side of the edge, then folded over and stitched from the other side, which gives more control over the placement. Either method gives a Class 3 seam, because the class is defined by the binding that encloses the edge, not by the number of steps used to apply it.

Where Class 3 seams are used

Bound seams are used where the inside of a garment will be seen, or where the raw edge needs protection and a neat finish. They appear on unlined jackets and coats, where the seam allowances are visible when the garment is worn open, on waistcoats, on bags, and on garments made from fabrics that fray readily. They also appear on necklines and armholes, where the binding encloses the edge and gives a clean finish without a facing.

The construction suits medium-weight fabrics that fray, and garments where a clean inside matters. It suits bias binding on curved edges, because a bias strip can follow a curve without puckering. It is less suited to very light fabrics, where the binding would add bulk and show through, and to very heavy fabrics, where the binding would make the seam too thick. It also takes more time than a plain finish, so it is used where the neat inside justifies the extra work.

Binding materials and widths

Binding can be made from the same fabric as the garment, from a contrasting fabric, or from a ready-made binding. Self-binding, cut from the garment fabric, matches the colour and weight and gives the neatest look, but it uses extra fabric and needs to be cut accurately. Contrasting binding can be a design feature, with a colour or pattern that shows on the inside of the garment. Ready-made bias binding is convenient and comes in a range of widths, but the colour and weight may not match the garment fabric exactly.

Width matters. A narrow binding gives a neat, light finish and suits a light or medium fabric. A wide binding gives more coverage and suits a fabric that frays heavily or a seam that needs extra protection. The binding should be wide enough to cover the raw edge fully on both sides, with a little extra for the stitching, but not so wide that it adds unnecessary bulk. Test the width on a scrap, including pressing, to see how it lies and whether it shows through the fabric.

Strengths and limits

The strengths of a bound seam are its neat appearance, its protection of the raw edge, and its durability. The binding encloses the edge completely, so fraying is stopped, and the extra layer of fabric adds strength to the seam. The finished inside looks clean and intentional, which suits garments that are worn open or that have no lining. A bound seam is also less likely to slip than a plain seam, because the binding adds a stable layer that the stitches can grip.

The limits are bulk, time, and visibility. The binding adds a layer of fabric along the seam, which can show through light cloth or add thickness at a point where several seams meet. Applying binding accurately takes time, especially around curves, and a binding that is stitched unevenly will look untidy. On a garment where the inside will never be seen, a simpler finish such as overlocking gives adequate protection with less work. Bound seams are a choice for the inside of the garment as much as for the seam itself, and that choice should be made with the garment in mind.

Checking a Class 3 seam

A well-sewn bound seam has binding that lies flat and even along the whole seam, with no raw edge showing on either side and no puckering where the binding curves. The stitching should catch the binding on both sides, with no places where the binding is loose or the edge is exposed. Press the seam after binding and check it in good light, because a binding that looks even while flat can show gaps when the garment moves.

When a specification calls for a Class 3 seam, check that the edge is wrapped in binding rather than simply overlocked or pinked. That wrapping is what defines the class. The width of the binding, the material it is cut from, and the number of stitch lines complete the specification, but the binding itself is the feature that makes the seam Class 3, and it is the feature to check first.