The Seam Line How seams are made, finished, and fixed

Home / French Seam on a Curved Seam

French Seam on a Curved Seam

A French seam can follow a gentle curve, but the enclosed fold resists bending, so curves need easing, careful pressing and a realistic limit.

Where curves and French seams meet

French seams are most at home on straight seams. The two pass method folds a strip of fabric back on itself, and a flat strip folds neatly. A curve asks that strip to bend while it folds, and the inner edge of the curve has less room than the outer edge. On a gentle curve, such as the side seam of a dress with a slight waist shaping, the difference is small and the fold can absorb it. On a sharp curve, such as an armhole or a tight neckline, the difference is too great, and the fold puckers or pulls.

The question to ask before starting is how tight the curve is. A curve that changes direction gradually over a long distance is workable. A curve that turns sharply over a short distance is not. The fabric matters too. A soft, fluid fabric eases around a curve more readily than a crisp, firm one, and a narrow enclosed fold bends more easily than a wide one. A scrap test on a curved offcut from the pattern gives a quick answer, and it is worth doing before committing to the real seam.

Some curved seams in a garment are good candidates. The curved side seam of a blouse, the princess seam of a dress with a gentle shape, and the curved hem of a skirt can all take a French seam if the curve is gentle.

Preparing the curve

Staystitching the curve before sewing the seam helps keep its shape. A line of stitching just inside the seam line, sewn with the fabric flat, stops the curve stretching out of shape while it is handled. This is especially useful on bias curves and on fabrics that stretch easily, such as silk and rayon. The staystitching sits inside the allowance, so it does not show on the finished garment.

Clipping and notching help the fold sit flat around the curve. On an outward curve, small clips cut into the allowance let it spread open. On an inward curve, small notches cut out of the allowance let it close up without bunching. The clips and notches are made after the first pass, in the trimmed allowance, and they should stop short of the stitching line so the seam is not weakened. They are only needed where the curve is tight enough to fight the fold.

Pressing the curve over a tailor's ham or a rolled towel, rather than flat on the board, supports the shape while the fold is pressed. A ham is a firm, curved cushion that lets the seam follow its natural shape instead of being flattened. If no ham is available, a rolled towel gives a similar support. Pressing a curved French seam flat on the board can distort the curve and leave the seam pulling.

Sewing the two passes on a curve

  1. Staystitch the curve if the fabric is prone to stretching, then place the pieces wrong sides together and pin along the curve.
  2. Stitch the first pass slowly, easing the fabric around the curve without stretching it.
  3. Press the first pass over a ham or a rolled towel, then trim the allowance evenly.
  4. Clip outward curves or notch inward curves in the trimmed allowance, stopping short of the stitching.
  5. Fold the pieces right sides together, press the fold over the ham, and pin to hold the curve.
  6. Stitch the second pass slowly, keeping an even distance from the fold, and press the finished seam over the ham.

Stitching slowly is the single most useful habit on a curve. The feed dogs move the fabric at a steady rate, and the sewer's job is to guide the curve gently, easing the layers together without pushing or pulling. Short seams can be sewn in one pass, but on a long curve it helps to stop with the needle down, lift the presser foot, and reposition the fabric, so the curve is never forced around a bend.

The fold after the first pass needs the same gentle handling. Forcing the fold around a tight curve bunches the fabric inside the fold, and the second pass then locks the bunching in. Easing the fold, pressing it over a ham, and pinning it in place before the second pass gives the stitching a fair chance of running straight and even.

Fixing puckering on a curve

Puckering on a curved French seam usually means the fold was not eased enough, or the curve was too tight for the method. The first thing to check is whether the puckering is in the first pass or the second. If the first pass puckers, the fabric was stretched while stitching, and restitching it more slowly, with staystitching, usually fixes it. If the first pass is smooth and the second pass puckers, the fold was not eased or pressed well enough.

Steam can help a mild pucker. Pressing the finished seam over a ham with steam, and letting it cool in shape before moving it, can relax the fibres and settle the fold. A stubborn pucker, where the fabric is visibly gathered along the seam, will not press out, and the honest fix is to unpick the second pass, ease the fold again, and restitch. It is a small repair, and it is better done now than after the garment is finished.

If the same curve puckers twice, the curve is probably too tight for a French seam in that fabric. Switching to a mock French seam, which has more give in the fold, or to a bound finish, which follows a curve easily, will give a better result. There is no fault in changing method when the fabric and the shape say so.

When to choose another finish

Sharp curves are the clearest case for a different finish. Armholes, sleeve caps, tight necklines and small pocket curves all fight the enclosed fold, and the result is often a puckered seam that looks worse than a simpler finish would. A bound edge, an overlocked finish or a narrow hem all follow a sharp curve more willingly, and they look tidier in the finished garment.

Very small curves, such as those on children's clothing or on a doll's garment, are also poor candidates, because the fold is wider than the curve itself and there is no room to ease it.

On a gentle curve, though, the French seam is worth the effort. It gives a sheer or lightweight garment a clean enclosed finish along a shaped seam, which is something an overlocked edge cannot do without showing through. The test is the scrap: sew the curve on an offcut, press it, and look at both sides. If it lies flat and smooth, the method works for that curve. If it puckers, the curve has given its answer.