The Seam Line How seams are made, finished, and fixed

Home / How to Sew a French Seam

How to Sew a French Seam

A French seam takes two passes of stitching, and the trick is to press and trim carefully between them so the second pass encloses the first.

Before you start

Check the pattern first. A French seam splits the total seam allowance across two passes, so the pattern allowance decides how wide each pass should be. If the pattern was drafted for a French seam, it will usually say so, and the allowance will already suit the method. If the pattern gives a standard allowance, the first pass takes a narrow share and the second pass takes the rest. The exact split depends on the total allowance, so read the pattern instructions rather than guessing.

Choose a thread that matches the fabric in weight as well as colour. A heavy thread on a sheer fabric leaves visible dots of stitching and can pucker the seam. A fine thread sits neatly and lets the fabric drape. A sharp, fine needle suits most lightweight wovens, and a fresh needle matters more than usual here, because a blunt needle can snag sheer fabric and leave a pulled thread that shows.

Cut the fabric pieces accurately and keep the edges aligned. The first pass is narrow, so there is little room to correct a wobbly cut later. If the edges are uneven, the trimming step becomes uneven too, and the second pass can end up trapping a raw edge outside the fold. A quick check of the cut edges before sewing saves more time than it costs.

Sewing the first pass

  1. Place the fabric pieces wrong sides together, which is the opposite of a normal seam, and pin along the seam line.
  2. Stitch the first pass with a narrow allowance, keeping the stitching straight and even.
  3. Press the seam to one side, then trim the allowance evenly to a narrow width, leaving enough fabric to enclose in the next step.
  4. Fold the fabric the other way, right sides together, so the first line of stitching is inside the fold, and press the fold flat.
  5. Stitch the second pass just beyond the fold, trapping the trimmed raw edges inside.
  6. Press the finished seam to one side and check from the right side that no raw edge is poking out.

The first pass sets up everything that follows. Because the pieces are wrong sides together, the seam allowance sits on the right side of the fabric at this stage. That looks odd the first time, but it is correct. The stitching line should be straight and the tension balanced, so the seam lies flat without puckering. If the first pass puckers, the second pass will lock the puckering in, so it is worth unpicking and restitching a bad first pass rather than pressing on.

Trimming is the step most people rush. The allowance should be trimmed evenly along the whole seam, close to the first stitching line but not so close that the stitches are nicked. Uneven trimming leaves a lumpy fold, and a fold that varies in width is hard to enclose cleanly. Small, sharp scissors or a rotary cutter give a cleaner trim than large dressmaking shears on a narrow allowance.

Sewing the second pass

After trimming, fold the fabric so the right sides are together and the first stitching line is hidden inside the fold. Press the fold firmly. The pressed fold is the guide for the second pass, so a crisp fold makes the stitching easier to keep straight. If the fold will not stay flat, a few pins placed across the seam, at right angles to the stitching line, will hold it in place without distorting the fabric.

The second pass is stitched just beyond the folded edge, far enough from the fold to trap the trimmed allowance completely inside. If the second pass runs too close to the fold, the raw edges can peek out of the seam. If it runs too far from the fold, the finished seam becomes wider than intended and the garment loses a little width at the seam. Keeping the stitching an even distance from the fold is what gives a neat, consistent result.

Stitch slowly on this pass, especially on sheer fabric. Sheer fabric can shift under the presser foot, and a fast pass can pull the fold out of line. Let the feed dogs move the fabric, and guide it gently rather than pushing or pulling. At the end of the seam, backstitch a few stitches to secure the thread, then press the finished seam to one side.

Pressing and checking the result

Press the finished seam from the wrong side first, with the iron set to a heat the fabric can take. Sheer fabrics scorch easily, so a press cloth is worth using on silk, organza and chiffon. Press the seam to one side, then turn the garment and check the right side. The seam should look like a plain straight seam, with no ridge showing through and no raw edge visible.

Check the wrong side too. The enclosed fold should be even in width along the whole seam, with no raw edge sticking out and no puckering. If a small piece of raw edge is showing, the second pass was stitched too close to the fold at that point. The fix is to unpick that section and restitch it slightly further from the fold. It is a small repair, and it is better done now than after the garment is finished.

On a curved seam, the same steps apply, but the fold needs more easing and the pressing needs a tailor's ham or a rolled towel to support the curve. Sharp curves are better avoided with this seam, and a gentle curve is the practical limit for most fabrics. If the curve is pulling or puckering, switching to a mock French seam or a bound finish may give a better result with less struggle.

Test the two passes on a scrap of the same fabric first. The scrap shows whether the thread, needle and stitch settings suit the fabric, and it gives a safe place to practise the fold before the real seam.