The Seam Line How seams are made, finished, and fixed

Home / Princess Seam on a Bodice

Princess Seam on a Bodice

A princess seam on a bodice runs from the shoulder or armhole through the bust to the waist. It is the most common place to meet this seam, and the bodice is where its fitting power shows most clearly.

Why the bodice

The bodice is the fitted part of a dress or top, covering the torso from shoulder to waist. It is where the body changes shape most: the shoulders slope, the bust is full, the waist is narrow. A bodice needs shaping, and a princess seam provides it along a single continuous line. That is why so many fitted bodices use princess seams instead of darts.

On a bodice, the seam does two jobs at once. It joins the panels of the bodice, and it shapes them. A bodice with princess seams has a centre front panel and two side front panels, and the same arrangement on the back if the back uses princess seams too. The panels are cut with curved edges, and joining them creates the three-dimensional shape of the torso from flat fabric.

The bodice is also where fit problems show first. A bodice that is too tight across the bust pulls at the princess seam. A bodice that is too loose at the waist bags at the same seam. Because the seam is long and visible, the maker can see the problem and fix it on the seam line, which is simpler than chasing the problem across several darts.

Shoulder or armhole start

On a bodice, the princess seam starts at the shoulder or at the armhole. The shoulder start gives a long line from the top of the bodice to the waist. It suits a bodice where the shoulder is plain and the seam line is meant to be a feature. The armhole start keeps the shoulder clean and puts the seam lower down, which suits a bodice with a shaped shoulder or a sleeve that needs a plain armhole.

The two versions are sewn the same way. The difference is in the pattern pieces: the shoulder version divides the bodice at the shoulder seam, while the armhole version divides it at the armhole. When choosing, consider the sleeve. A set-in sleeve attaches to the armhole, and a princess seam that starts at the armhole meets the sleeve seam at that point. That junction needs care, since three seams meet there, but it is a standard construction and patterns are drafted to handle it.

Some bodices use a princess seam on the front only, with darts on the back. Others use princess seams front and back. A back princess seam shapes the shoulder blades and the waist in the same way the front seam shapes the bust. Using the seam on both sides gives a balanced fit, but it also doubles the curved sewing, so a first bodice often uses the seam on the front only.

Sewing the bodice seam

  1. Mark the seam line and the bust point on each bodice panel before joining anything.
  2. Pin the centre front panel to a side front panel, right sides together, starting at the bust point and working outward in both directions.
  3. Sew from the shoulder or armhole down to the waist, easing the longer curved edge into the shorter one and sewing slowly through the bust point.
  4. Clip the seam allowance on the tightest part of the curve, stopping just short of the stitching.
  5. Press the seam open or to one side over a tailor's ham, supporting the curve as you press.
  6. Repeat for the other side, then check that the two seams mirror each other before joining the bodice to the skirt or waistband.

Fitting the bust on a bodice

The bust is the key fitting point on a bodice with princess seams. The deepest part of the curve should sit at the fullest part of the bust. If the curve sits too high, the bodice will pull above the bust and wrinkle below it. If it sits too low, the bodice will bag at the top and pull underneath. Mark the bust point on the body while trying the bodice on, and compare it with the pattern.

Room across the bust is added by letting the seam out over the fullest area, blending back into the original line above and below. A centimetre of extra room at the bust, spread along the curve, can make a bodice comfortable without changing its look. The change should be gradual: a sudden change in the seam line will show as a kink.

The waist of the bodice is fitted in the same way, by taking the curve in or letting it out at the waist. The waist is where the bodice meets the skirt, so a good fit here matters for the whole dress. If the bodice waist is loose, the skirt will hang from the wrong place. If it is tight, the dress will be uncomfortable to sit in.

Joining the bodice to a skirt

Once the princess seams are sewn and the bodice fits, the bodice is joined to the skirt at the waist. The waist seam should be checked against the skirt waist: the two should be the same length, and the princess seams should line up with the skirt seams or darts where they meet. A princess seam that ends at the waist can continue visually into a skirt seam, which gives a dress a long, clean line.

Press the waist seam before attaching the skirt, and keep the bodice panels flat while pinning. The curved princess seams can pull the waistline out of shape if the bodice is handled roughly at this stage. Pin the bodice to the skirt at the princess seams first, then at the centre and sides, so the joins stay aligned.

After the waist seam is sewn, try the dress on again. The bodice fit can change once the weight of the skirt pulls on it, especially in a heavier fabric. A bodice that fitted perfectly on its own may need a small adjustment at the princess seam once the skirt is attached. That is normal, and it is easier to adjust the seam now than after the lining is in.

A bodice with princess seams is a fitted garment that can be adjusted along one line. Get the bust point in the right place, keep the curve smooth, and the rest of the dress will follow from it.