The Seam Line How seams are made, finished, and fixed

Home / Princess Seams: What They Are and How They Shape a Garment

Princess Seams: What They Are and How They Shape a Garment

A princess seam runs in a long curve from the shoulder or armhole, down through the bust, and on to the hem. It shapes a garment along a line instead of pinching it at a point, which gives a smooth, close fit without visible darts.

What a princess seam is

A princess seam is a shaped seam that divides the front or back of a garment into panels. It begins at the shoulder or at the armhole, curves in toward the waist, passes over the fullest part of the bust, and continues down to the hem. The seam line itself does the shaping work. Instead of folding fabric into a dart at one spot, the curve takes in fullness gradually along its whole length.

Most princess seams start at one of two places. A shoulder princess seam begins at the shoulder seam and curves down through the bust. An armhole princess seam begins at the armhole, usually near the middle of the armhole curve, and follows the same path down. Both versions shape the same area. The choice between them is a style decision, and it changes where the seam line shows on the finished garment.

How the curve creates the shape

The curve of a princess seam is not a decoration. Its depth and position decide how much shaping the garment gets. A deeper curve pulls the fabric in more at the waist. A straighter line gives a looser, more relaxed fit. The tightest part of the curve usually sits at the bust point, where the body is fullest, and the line eases out above and below that point.

Getting the curve right matters more than getting it exactly symmetrical at first. The two sides of a garment should match, but the curve itself should follow the body it is made for. On a pattern, the curve is drawn as a smooth line. When the two panels are pinned together, the curved edges must meet exactly along the seam line, even though one edge may be longer than the other. The extra length is eased in as the seam is sewn, which is what lets a flat piece of fabric wrap around a curved body.

A common mistake is to sew the curve too sharply. A sharp bend at the bust point creates a point or a wrinkle, and the seam will not lie flat. A gentle, gradual curve sews more cleanly and presses better. If the pattern curve looks angular, smooth it out before cutting. Small changes to the curve make a visible difference in the finished garment.

Where princess seams are used

Princess seams appear most often in fitted dresses. A dress with princess seams needs no waist darts, and the long seam lines give it a clean, tailored look. The same construction shows up in fitted jackets, where the seams run from the shoulder or armhole through the waist and continue to the hem or to the jacket edge. Coats use princess seams too, usually with a straighter line so the coat has room to move.

Blouses and tops with a close fit use princess seams for the same reason. The seam lines add shape without adding bulk at the waist, and they give the maker a place to adjust the fit. On a blouse, the seam may stop at the waist or continue to the hem, depending on the style. Some tops use a princess seam only on the front, with a plain back, which is a simpler version of the same idea.

Fitting a princess seam

Fitting happens by adjusting the curve, not by adding darts. If the garment pulls across the bust, the curve needs more room at that point, which means letting the seam out slightly over the fullest area. If the waist is loose, the curve needs to be taken in more at the waist. Because the seam runs the full length of the garment, a change at one point affects the line above and below it, so adjustments are best made in small steps.

A toile, or test garment, is the usual way to check the fit before cutting good fabric. Sew the princess seams in the test fabric, try the garment on, and mark where the curve needs to move. Pin the seam deeper or let it out, then check the line again. The seam should fall straight from the shoulder to the hem when viewed from the front, with the curve following the body rather than pulling to one side.

Puckering at the curve is the most common problem. It usually means the seam was sewn too fast, the curve was too sharp, or the fabric was pushed rather than eased along the line. Slowing down, clipping the seam allowance on the tightest part of the curve, and pressing the seam over a curved surface all help. A seam that puckers after pressing often needs the curve itself redrawn, not just more pressing.

Sewing and pressing the curve

A princess seam is sewn with the pieces pinned together along the marked line, easing the longer edge into the shorter one. Short pins placed close together keep the curve aligned. Sewing slowly around the bust point gives the feed dogs time to move the fabric evenly. A shorter stitch length can help on a tight curve, since it gives more control at the point where the line changes direction.

After sewing, the seam allowance on a curved seam needs clipping or notching so it can spread and lie flat. On an outward curve, small clips cut into the allowance let it open out. On an inward curve, small notches cut out of the allowance remove bulk. The cuts should stop just short of the stitching, never through it. Pressing comes next, and a tailor's ham, a firmly stuffed curved cushion, supports the curve while the iron shapes it. Pressing a curved seam flat on a table flattens the shape the seam was meant to create.

Princess seams and darts, side by side

A dart shapes fabric at a point. It folds a wedge of fabric and stitches it to a taper, which pulls the garment in at one place. A princess seam shapes fabric along a line. It divides the garment into panels and uses the curve of the seam to create the same shaping over a longer distance. Both methods fit a garment. The difference is where the shaping happens and how it looks.

Princess seams suit garments where a long, smooth line is part of the design. They also suit bodies where a single dart would need to be very deep, since spreading the shaping along a line avoids a sharp point. Darts suit simpler garments and fabrics where a long curved seam would be hard to sew. Many garments use both, with princess seams on the front and darts on the back, or the other way round.

Choosing between them is a matter of style, fabric, and the fit needed. A pattern that uses princess seams can be adjusted at the seam line, which makes fitting a matter of moving one continuous line. A pattern that uses darts is adjusted by moving or reshaping the dart. Either approach works when the pattern is fitted carefully and the seam or dart is sewn and pressed well.

Start with the curve, not the fabric. Draw the seam line smooth, sew it slowly, and check the fit on the body before the garment is finished, and a princess seam will give a closer, cleaner fit than a row of darts ever could.