How to Sew a Princess Seam
A princess seam is sewn slowly, with the curved edges pinned closely and eased together. The work is in the preparation: mark the curve clearly, pin it well, and the stitching follows.
Before you start
Check the pattern pieces first. Each panel of a princess seam has a curved edge, and the two edges that join must be the same length along the seam line, even though they look different. Match the notches on the two pieces. If the notches do not line up, the pieces are not a pair, or one of them is the wrong way round. Sorting this out before cutting saves fabric.
Transfer the seam line to the fabric. Marking the stitching line, not just the cutting line, matters on a curve, because the eye cannot judge a curve the way it can judge a straight edge. Use tailor's chalk, a washable marker, or a line of basting stitches. Mark the bust point too, since that is where the curve changes direction and where the most care is needed.
Cut the pieces carefully, keeping the seam allowance even. An uneven allowance changes the curve when the pieces are joined, and the seam will not sit where the pattern intended. If the fabric frays, finish the edges after cutting, or handle the pieces gently until the seam is sewn.
Marking and pinning the curve
Lay the two panels right sides together and match the notches. Start pinning at the bust point, then at the top and bottom ends of the seam, then fill in between. Pins should sit close together on a curve, about a finger width apart, and they should cross the seam line at a right angle so the layers cannot shift.
One edge of the curve is usually longer than the other. The longer edge has to be eased into the shorter one as the seam is sewn. Pinning in short sections keeps that easing even. If a section of the longer edge will not lie flat, it needs more pins, not more force. Forcing the fabric creates puckers that will show on the outside.
Check the pinned seam before sewing. The curve should look smooth from the edge, with no kinks or flat spots. If a kink appears, remove the pins around it and repin. A kink pinned into the seam becomes a kink sewn into the seam, and it is harder to fix afterwards.
Sewing the seam
- Set the machine to a normal straight stitch. A shorter stitch length gives more control on the tightest part of the curve.
- Start at the top of the seam, at the shoulder or armhole, and sew with the longer edge on top if possible, so the feed dogs can ease it in.
- Sew slowly through the bust point, turning the fabric gently so the needle follows the marked line. Stop with the needle down and lift the presser foot to reposition the fabric when the curve turns sharply.
- Keep the seam allowance even as you sew. Watch the marked line, not the edge of the fabric, since the edge is curved and the allowance can drift.
- Continue to the hem, keeping the same slow pace. Do not pull the fabric from behind the needle, since pulling stretches the curve.
- Check the seam from the right side. It should form a smooth curve with no puckers. If a pucker appears, unpick back past it and resew that section with more easing.
Clipping and pressing
After sewing, the seam allowance needs to be shaped so the curve can lie flat. On the parts of the curve that bend outward, cut small clips into the allowance, stopping just short of the stitching. On the parts that bend inward, cut small notches out of the allowance to remove bulk. Space the cuts a couple of centimetres apart, closer together where the curve is tightest.
Press the seam open or to one side, following the pattern instructions. A tailor's ham, a firmly stuffed curved cushion, is the right tool here. Lay the seam over the ham so the curve is supported, and press with the tip of the iron. Pressing a curved seam flat on a table irons out the shape the seam was meant to create, so the curve should be supported while it is pressed.
Press from the wrong side first, then check the right side. The seam line should be smooth and the panels should lie flat. If a ripple remains, the seam allowance may need another clip, or the seam may need to be resewn with more easing at that point. Pressing alone cannot fix a seam that was sewn with too much fullness in one place.
Checking the fit
Try the garment on once the princess seams are sewn and pressed. The seam should fall in a smooth line from the shoulder or armhole to the hem, following the body without pulling to one side. The bust point of the seam should sit at the fullest part of the bust. If it sits too high or too low, the pattern needs adjusting, not the seam.
Common fit faults show up clearly on a princess seam. If the seam pulls across the bust, the curve needs more room there. If the waist is loose, the curve needs to be taken in more. If the seam twists, one panel was probably cut or sewn slightly off, and the seam line needs to be checked against the pattern. Small changes, a few millimetres at a time, are safer than large ones.
Mark any changes on the garment while wearing it, then transfer them to the pattern. A princess seam that has been fitted once becomes a reliable pattern for the next garment in the same fabric. Keep the corrected pattern, and the next princess seam will be faster.
Sew the curve slowly, ease rather than pull, and press over a ham. Those three habits are what separate a smooth princess seam from one that puckers at the bust.