Lapped Seams
A lapped seam overlaps one edge over the other. The stitching goes through the overlap, and the result is a flat join with no pressed open allowance underneath.
What a lapped seam is
Lapped seams are class 2 in the standard classification. One piece is laid over the other so the edges overlap, and the stitching goes through the overlapped layers. The raw edge of the top piece is usually folded under first, so no raw edge shows on the right side. The raw edge of the under piece sits inside the overlap, protected by the top layer.
The seam is the join, and the stitch is the single loop of thread that makes it. In a lapped seam, the stitches are usually visible from the right side, running along the folded edge of the top piece. That visible line is part of the seam, not decoration added to it, though it often looks decorative.
Lapped seams lie flat because there is no allowance pressed open underneath. The layers sit on top of each other rather than side by side, so the seam has a low profile. That flatness is the main reason to choose this seam, and it matters most on fabrics that are thick, stiff, or hard to press.
How to sew one
Prepare the top piece first. Fold its edge under by the overlap amount and press the fold, so the folded edge is straight and the raw edge is hidden inside the fold. The overlap amount is usually the seam allowance, often 5/8 inch on garments, but the pattern should always be checked, since allowances vary.
- Mark the stitching line on the under piece, and mark the fold line on the top piece.
- Fold the top piece edge under at the fold line and press it.
- Lay the folded edge of the top piece along the stitching line of the under piece, matching any notches.
- Pin or baste the overlap in place, checking that the overlap width stays even along the whole seam.
- Stitch close to the folded edge, through all layers, keeping the distance from the fold even.
- Press the finished seam flat from the right side, using a pressing cloth if the fabric marks easily.
Accuracy in the overlap is what makes a lapped seam look good. If the overlap is wider in one place than another, the stitching line wanders and the seam looks uneven. Basting the overlap before stitching is worth the time on a long seam.
Where lapped seams are used
Lapped seams are used on fabrics that do not press well. Leather and vinyl cannot be pressed open in the usual way, since heat marks them and the crease stays, so a lapped seam that is topstitched flat is a practical join. Heavy coating and canvas behave similarly, and a lapped seam keeps the join flat without a fight at the ironing board.
They are also used where a flat join matters for comfort or for the look of the garment. A lapped seam on a shirt yoke or a jacket panel lies flat against the body and does not create a ridge. On upholstery, lapped seams give a flat join that does not press a line into the padding underneath.
Children's clothing sometimes uses lapped seams on the inside, since the flat join does not rub against the skin the way a pressed open allowance can. The same idea applies to linings and to garments worn close to the body.
Lapped seams and topstitching
Topstitching is part of most lapped seams. The stitching that holds the overlap is done from the right side, close to the folded edge, and it shows. A second row of stitching, further from the edge, is often added for strength and for appearance. The two rows together hold the overlap flat and spread the load.
The thread used for topstitching is often slightly heavier than the thread used for the rest of the garment, and the stitch length is often slightly longer, so the stitching reads as a design feature rather than a construction line. The choice is a matter of the look wanted, and the pattern or the garment style usually suggests it.
On leather and vinyl, topstitching needs care, since every needle hole stays visible. A stitch that has to be removed leaves holes, so the seam should be basted with tape or clips rather than pins, and the stitching should be tested on scrap first.
Strengths and limits
The strengths of a lapped seam are flatness, strength, and a tidy right side. The overlap gives two layers of fabric at the join, the topstitching spreads the load, and there is no raw edge showing. The seam presses easily, or needs no pressing at all on fabrics that cannot be pressed.
The limits are accuracy and adjustment. The overlap must be marked and held even, which takes more preparation than a plain superimposed seam. A lapped seam is also hard to adjust after sewing, since letting it out means moving the overlap, and the old stitch holes and fold line may show. Fitting changes should be made before the lapped seam is sewn, not after.
A lapped seam is a practical choice rather than a default one. It suits the fabrics and the places where flatness matters, and it asks for careful marking in return. On those projects it gives a join that lies flat, looks tidy, and holds well, with no pressing fight at the end.