ISO 4916 Lapped Seams (Class 2)
Lapped seams are ISO 4916 Class 2. In this construction the fabric pieces overlap, with the edge of one piece lying over the other, and the stitching passes through the lapped layers to hold them together.
How a lapped seam is built
The construction starts with the two pieces placed so that they overlap by the width of the seam allowance. The edge of the upper piece lies over the lower piece, and a line of stitching is sewn through the overlapped area, usually near the folded or raw edge of the upper piece. A second line of stitching may be added for strength or appearance, particularly on garments that take strain. The raw edge of the lower piece is usually enclosed or finished, while the edge of the upper piece may be folded under before stitching so that no raw edge shows on the right side.
The overlap can be arranged in several ways. In the simplest form, the pieces overlap with raw edges, and the stitching holds them together. In a folded form, the edge of the upper piece is turned under before it is lapped over the lower piece, which gives a clean edge on the right side. The class covers all of these variations, because the defining feature is the overlap, not the folding or the number of stitch lines.
Where Class 2 seams are used
Lapped seams are used where a flat, strong seam is needed, or where the seam will be visible and should look neat from the right side. They appear on jeans, where the flat-felled seam is a well-known lapped construction, on shirts, where a lapped seam gives a flat finish on the inside, and on tailored garments, where a lapped seam can be topstitched for a clean, structured look. They also appear on leather and vinyl, where a superimposed seam would be bulky and hard to press, and where lapping the pieces gives a flatter join.
The construction suits fabrics that are stable and hold a fold well, such as denim, cotton shirting, and medium-weight wool. It suits garments that take strain, because the overlap spreads the load across a wider area than a single stitch line, and a second row of stitching adds further strength. It is less suited to very light or sheer fabrics, where the overlap would show through, and to fabrics that do not hold a pressed fold.
Flat-felled seams and Class 2
The flat-felled seam is the best-known example of a lapped seam. It begins with the pieces placed together, then one allowance is trimmed, the other is folded over it, and the folded edge is stitched down. The result is a seam with two lines of stitching, no raw edges showing, and a flat profile that lies neatly against the garment. It is strong, it wears well, and it looks clean from both sides, which is why it is used on jeans, workwear, and shirts.
Not every lapped seam is a flat-felled seam. A lapped seam with a single line of stitching and a raw edge is still Class 2, as is a lapped seam where the upper edge is folded under but not stitched down a second time. The flat-felled seam is one member of the class, not the whole class. Knowing that distinction helps when reading a specification: a call for a Class 2 seam does not by itself mean a flat-felled seam, and a flat-felled seam should be specified as such if that is what is wanted.
Strengths and limits
The strengths of a lapped seam are its flatness, its strength, and its neat appearance. The overlap spreads strain, the folded edge encloses raw edges, and the seam lies flat without the bulk of two allowances pressed to one side. A lapped seam with two stitch lines is stronger than a plain superimposed seam of the same fabric, and it is less likely to slip, because the stitches pass through more layers.
The limits are that lapped seams take more time and care to sew than a plain seam, and they need accurate folding and alignment. If the overlap is uneven, the seam will look wavy and the stitch line will wander. The construction adds bulk where the layers overlap, which can be a problem on thick fabric or at a point where several seams meet. It also uses more fabric than a plain seam, because the overlap needs a wider allowance. On a curved seam, lapping is harder to control, and the fold may not lie flat around the curve.
Press the fold before stitching a lapped seam. A fold that is pressed accurately gives a straight stitch line, while a fold that is only finger-pressed can drift and leave a wavy seam.
Checking a Class 2 seam
A well-sewn lapped seam lies flat, with the overlap even along its whole length and the stitch line straight and at an even distance from the folded edge. The raw edges should be enclosed or finished, with no fraying showing on the right side. Pull the seam gently across the stitch line to check that it holds, and check the ends for any place where the overlap narrows or the stitching misses the lower layer.
When a specification calls for a Class 2 seam, check that the pieces overlap rather than lying face to face. That overlap is what defines the class. The number of stitch lines, the folding of the edge, and the finish complete the specification, but the overlap is the feature that makes the seam Class 2, and it is the feature to check first.