How to Sew a French Seam Pillowcase
A French seam pillowcase is sewn in two passes on each seam. The first pass joins the fabric, the second encloses the raw edges, and the result is a case with no fraying edge anywhere.
What You Need
The project needs fabric, thread to match, scissors or a rotary cutter, pins, a ruler, and a sewing machine, though the seam can also be sewn by hand. Cotton is the simplest fabric for a first case, since it presses well and folds neatly. The thread should match the fabric, since the stitching will show on the inside of the seam and at the cuff. An iron is important, because pressing between the two passes is what makes the French seam lie flat.
Measure the pillow before cutting. Lay the pillow flat, measure its length and width, and add enough extra for the seam allowances and for ease, so the case slips on without straining. The cuff is a folded band at the open end, so its depth is added to the length as well. Cut the fabric as a rectangle, keeping the grain straight so the case does not twist.
Preparing the Cuff
The cuff is usually made first. Fold the fabric at the open end to form a band, press the fold, and stitch the cuff in place along its inner edge. Some methods sew the cuff as a separate band and join it to the case, while others fold the case fabric itself to form the cuff. Either way, the cuff should be pressed neatly, since it is the most visible part of the finished case and the first thing seen when the pillow is put on the bed.
The cuff fold should be pressed before the side seams are sewn, so the fold is already set when the case is turned and stitched. A cuff that is pressed after the seams are done will never lie as flat, since the side seams hold the fabric in place and resist the fold. Pressing the cuff first also makes it easier to check that the cuff is even along its whole length before it is locked in by the side seams.
If the cuff is made from a contrasting fabric, it is sewn to the case before the side seams are done, so the join is enclosed in the French seam. The cuff edge should be finished, either by folding it under or by enclosing it, so no raw edge shows at the opening. A cuff that is pressed flat and stitched evenly gives the case a clean, finished look.
Sewing the French Seams
- Place the fabric wrong sides together, matching the raw edges along the seam line.
- Sew the first pass with a narrow seam allowance, keeping the stitching straight and even.
- Trim the allowance close, so the first seam is slim enough to enclose.
- Press the seam to one side, then turn the case so the right sides are together.
- Press the seam again, folding the fabric so the first stitching sits inside the fold.
- Sew the second pass with a slightly wider allowance, enclosing the first seam completely.
- Press the finished seam flat and check that no raw edge shows on either side.
Finishing the Case
Once the side seams are sewn, turn the case right side out and check the fit on the pillow. The case should slip on easily and sit smoothly, without pulling at the seams or bunching at the corners. Press the case, paying attention to the cuff, which should lie flat and even. The corners can be pushed out gently with a blunt tool so they sit square, though care is needed not to poke through the fabric.
Check the seams from the inside as well as the outside. A good French seam looks neat on both sides, with the enclosed edge fully hidden and the second row of stitching catching it all along the seam. If a section of the first seam peeks out, it can be restitched, since the second pass is the one that does the enclosing.
Pre-washing the fabric before cutting is worth doing, since cotton can shrink and a case that fits before washing may be tight afterwards. Press the fabric flat before measuring, since creases can throw the measurements off, and cut with the grain straight so the finished case does not twist. A little care at the cutting stage makes the sewing much easier, and the case will fit the pillow properly from the first wash onwards.
Fixing Common Problems
The most common problem is a first seam that is too wide to enclose, so the raw edge pokes out of the second seam. Keeping the first pass narrow and trimming it close before the second pass avoids this. Another common problem is a seam that puckers, which usually means the layers fed unevenly or the thread tension was too tight for the fabric. Sewing slowly and testing the tension on a scrap will help.
If the case comes out too tight, the seams can be let out slightly by restitching with a narrower allowance, though this is only possible if there is enough fabric in the seam. Measuring the pillow carefully before cutting is the better fix, since a case that fits from the start does not need adjusting. A case that is a little loose is more comfortable than one that strains its seams.
Take the time to press between the passes and to test the stitching on a scrap, and the case will come out clean. The French seam does the hard work, hiding every raw edge and giving the pillowcase a finish that looks far more polished than the effort it takes.