Seams on Upholstery Fabric
Upholstery fabric is thicker, stiffer, and harder to feed than dressmaking fabric, so its seams need a different approach from the first stitch.
How Upholstery Fabric Behaves Under the Needle
Most upholstery fabrics are woven tightly and may carry a backing that stiffens the cloth and stops it fraying. That backing makes the fabric strong, but it also makes it resist the needle and the feed dogs. Layers can slip against each other, and a seam that looks straight on top can drift underneath. Testing on a scrap of the same fabric is the simplest way to find out how it behaves before cutting into the real pieces.
Some upholstery fabrics have a nap or a raised surface, such as velvet, which changes direction when brushed. Seams on these fabrics need the nap running the same way on both sides, or the finished piece will show a visible difference in shade along the seam. Patterned fabrics add another concern, since a pattern that does not line up across a seam will draw the eye straight to the join.
Backed fabrics bring their own problems. The backing can make the fabric stiffen and resist folding, so a seam allowance that would press flat on an unbacked fabric may spring back and stand up. In that case, trimming the allowance closer and topstitching it down will hold it in place. A backing can also dull needles faster than plain fabric, so the needle should be checked and changed if the stitching starts to skip or the fabric starts to show pulled threads along the seam line.
Choosing a Seam for the Fabric
A plain seam works well on flat panels of woven upholstery fabric, where the seam will sit out of sight. On visible edges, a welt seam adds a cord that protects the edge and gives it a firm shape. Where the fabric is very thick, a lapped seam keeps the join flat because the layers overlap instead of stacking up in a bulky fold. The choice depends on where the seam sits, how much it will be seen, and how thick the layers are.
French seams, which enclose raw edges, are sometimes used on upholstery fabric for a clean inside finish, though they add bulk and are harder to sew through heavy cloth. On lighter upholstery fabrics they can work well, especially on cushion covers that will be turned and handled often. The seam type should suit both the fabric weight and the way the finished piece will be used.
Seam allowance width deserves a decision of its own. On heavy upholstery fabric, a wider allowance gives the stitching more to grip and allows grading, but it also adds bulk that has to be trimmed. A narrow allowance lies flatter but can pull out under strain. The allowance should be wide enough to hold and to trim, and it should be the same width all along the seam, since an uneven allowance will press unevenly and the seam will wander.
Thread and Stitch Length
Strong thread is essential on upholstery fabric, since the seam takes repeated pulling and rubbing. A heavy thread made for upholstery resists abrasion better than ordinary thread, and it holds the thick layers together without snapping. The needle needs to match the thread and the fabric, so it punches a clean hole without damaging the weave. A needle that is too fine will bend or break on heavy fabric, while one that is too coarse will leave visible holes.
Stitch length needs care as well. Stitches that are too short punch many holes close together and can weaken the fabric along the seam line. Stitches that are too long leave the seam loose and open to pulling apart. A middle length, tested on a scrap, usually gives the best balance. Double stitching, a second row close to the first, adds strength on seams that take the most strain, such as seat seams and cushion edges.
Feeding Thick Layers Evenly
The hardest part of sewing upholstery fabric is often getting the layers to feed evenly. The top layer can creep forward while the bottom layer lags, leaving a seam that puckers or drifts. Pins or clips placed across the seam line hold the layers together, and a walking foot helps by feeding the top and bottom layers at the same rate. Sewing slowly gives the machine time to move the heavy fabric through without bunching.
When a seam crosses a join where several layers meet, the bulk can stop the foot from sitting flat. Trimming and grading the seam allowance, so each layer is cut to a slightly different width, reduces the step at the edge. On curves, clipping the allowance lets the fabric turn smoothly instead of pulling the seam out of shape.
Always test on a scrap of the same fabric first. Needle holes in coated or backed upholstery fabric do not close up, so a wrong stitch length or a crooked test line on the real piece cannot be undone cleanly.
Finishing the Seam
After stitching, the seam allowance on upholstery fabric is usually trimmed to reduce bulk, and the raw edge may be overlocked or bound so it does not fray inside the cover. On a cushion cover, the seam allowance is often pressed to one side and topstitched down, which keeps the seam flat and stops the allowance from shifting when the cushion is used. Pressing needs a cloth between the iron and the fabric, since direct heat can mark or flatten the surface of many upholstery fabrics.
The finished seam should lie flat, feel firm, and show even stitching. If it ripples or pulls, the cause is usually uneven feeding or thread tension that does not suit the fabric, and both are easier to fix on a test scrap than on a finished cover. A seam that is planned around the fabric, rather than forced through it, will hold its shape for years.