Seams on Jeans
The seams on a pair of jeans are doing two jobs: holding the garment together through hard wear, and giving jeans their familiar look.
Which Seams Appear on Jeans
Several different seams appear on a typical pair of jeans, and each one suits its position. The inseam and outseam, which run down the legs, are usually flat-felled, since those seams take a lot of strain and need to lie flat against the leg. The waistband is attached with a topstitched seam, and the yoke at the back is sewn with a flat-felled or topstitched seam that follows its curve. Pocket openings are reinforced with topstitching and often with bar tacks, small dense rows of stitching that stop the pocket from tearing away.
The crotch seam is the hardest working seam on jeans, since it takes pull from every direction when the wearer sits, walks, and bends. It is usually sewn with a strong seam and reinforced, and the bulk at the join where the inseams meet is trimmed and graded so the seam lies flat. A seam that is bulky at the crotch will rub and wear faster than a flat one.
Flat-Felled Seams on Jeans
The flat-felled seam is the signature jeans seam. It encloses the raw edges inside a fold, so nothing frays, and it is stitched through several layers, which makes it very strong. On the outside, it shows two parallel rows of stitching, which is the look most people associate with jeans. The seam is sewn wrong sides together first, then one allowance is trimmed, the other is folded over it, and the fold is topstitched down.
Flat-felled seams work best on straight runs such as the leg seams. On curves, such as the yoke, the fold has to be pinned carefully so it stays even as the seam turns. The topstitching has to catch the folded edge all along the seam, or the fold will lift and the raw edge may show. Sewing slowly and checking the fold as you go keeps the seam neat.
Topstitching and the Jeans Look
Topstitching is what makes jeans look like jeans. The twin rows of stitching along the legs, pockets, and waistband are sewn in a contrasting thread, usually a warm gold or orange, and they have to be straight and even because they are on show. The stitching is sewn with strong thread and a longer stitch length than on lighter garments, which suits the heavy denim and gives the stitching its characteristic look.
Double-needle topstitching sews both rows at once, which keeps the spacing even and saves time on long seams. The rows are placed close to the seam line and along the edge of the folded allowance, so they hold the seam flat as well as decorating it. Uneven topstitching is one of the first things that marks a pair of jeans as poorly made, so the stitching deserves as much care as the seam itself.
Seams on Jean Pockets
Pockets are where jeans seams work hardest in a small area. The pocket opening is pulled every time a hand goes in, and the pocket bag hangs from the waistband and swings with every step. The opening is usually finished with a folded edge and topstitched, and the corners are reinforced with bar tacks, small dense blocks of stitching that stop the fabric from tearing at the point where the pull is strongest. Without those bar tacks, the pocket opening would split away from the leg surprisingly quickly.
The pocket bag itself is sewn with a French seam or an overlocked seam, since the inside of the pocket is handled and washed and the raw edges would fray. The bag is attached to the leg along a curved seam, which has to be clipped so it can turn smoothly, and the seam is often topstitched so it lies flat against the leg. A pocket that is sewn well feels smooth and stays in place, while a pocket with a bulky or puckered seam will twist and show through the leg of the jeans.
What Makes Jeans Seams Fail
Jeans seams usually fail in one of three ways. The thread wears through along a seam that takes constant rubbing, such as the inseam. The fabric tears along the stitching holes where the denim has thinned with wear, often at the crotch or the pocket corners. Or the seam splits because the stitching was too short or the thread too light for the strain. Each failure points to a different cause, and a repair that ignores the cause will not last.
Repairing a jeans seam usually means restitching with strong thread and, where the fabric is thin, adding a patch behind the seam to give the stitching something sound to grip. A seam that is restitched through worn fabric will pull out again, so the patch matters as much as the thread. Bar tacks at pocket corners and stress points help stop a seam from splitting in the first place.
Making Jeans Seams Last
The best jeans seams are made with strong thread, a heavy-duty needle made for denim, and a stitch length suited to the fabric weight. The seam allowance is trimmed and graded where layers stack up, the seam is pressed flat before topstitching, and the topstitching is sewn slowly and evenly. Washing also plays a part: frequent hot washing wears both the thread and the fabric, so gentler washing and air drying help the seams last longer.
Jeans seams are a good example of form following use. They are flat because flat seams are comfortable, strong because jeans are worn hard, and topstitched because the stitching is part of the design. A seam that does all three will hold up for years.