Flat-Felled Seam on Shirts
A flat-felled seam on a shirt looks quiet and tidy. It holds the shoulder, side and sleeve seams flat, encloses the raw edges, and survives repeated washing without fraying.
Where it is used on a shirt
The classic places for a flat-felled seam on a shirt are the shoulder seams, the side seams and the sleeve seams, including the underarm seam that runs from the cuff to the side. These are long, straight seams, which suit the folding method, and they are the seams most likely to be seen when a shirt is worn untucked or with the sleeves rolled. On a men's shirt, the yoke seam across the shoulders is often flat-felled as well, and the same finish appears on the seams of a work shirt or a uniform shirt. The seam sits flat against the body, so it does not create a ridge under a jacket or a sweater, and it looks clean from the inside when the shirt is taken off or hung up. That inside view matters on a shirt, because the inside is often visible at the collar, the cuffs and the placket. A shirt with enclosed seams looks finished rather than half made, even before it is pressed.
What the seam does for a shirt
Shirts are washed often, and a seam that frays in the wash soon looks worn, even if the fabric is still sound. The flat-felled seam folds the raw edges inside, so washing cannot fray them, and the double stitching holds the seam together through many laundry cycles. The seam is also strong, which helps at the shoulder and the underarm, where the fabric is pulled when the wearer reaches or lifts. On a lightweight cotton shirt, the seam adds a little structure without adding bulk, and the topstitching gives a neat, tailored line that suits the style of the garment. The flat profile is comfortable too: a seam that stands up inside a shirt can rub at the shoulder or the side, while a flat-felled seam lies smooth. For a shirt that is worn often and washed often, that combination of durability, comfort and a clean inside is hard to beat.
Fabric and stitch choices
Shirting cotton, poplin, chambray and lightweight linen all take a flat-felled seam well, because they press crisply and fold without too much bulk. The stitch length should suit the weight of the cloth: a shorter stitch on a fine cotton, a slightly longer stitch on a heavier chambray or Oxford cloth. Thread to match the fabric keeps the topstitching subtle, which is usually the aim on a shirt, though a contrast thread can be a design choice on a casual shirt. A fine needle, suited to the fabric weight, avoids leaving visible holes in a light cloth. Pressing is important on shirting, since a crease pressed into the fold stays put and the topstitching follows it. Test the fold and the stitch length on a scrap of the shirt fabric, pressed in the same way, before sewing the shirt itself. The scrap shows whether the fold is too wide for the cloth, whether the topstitching puckers, and whether the seam lies flat.
Sewing it on a shirt
The method is the same as for any flat-felled seam, but the scale is smaller and the pressing needs more care. Sew the seam with the right sides together, trim one allowance, fold the other over it, press, and topstitch close to the folded edge. On a shirt, the seams are often long and the fabric is light, so pin or clip the fold at intervals to stop it shifting. Work in sections on the side seam, pressing as you go, rather than trying to fold the whole length at once. At the underarm, where the sleeve seam meets the side seam, the layers stack up, and the fold needs to be eased around the join rather than forced flat. Turn the shirt right side out and check the topstitching from the outside before pressing the finished seam, since a fold that has slipped will show as a wavy line. A sleeve board or a seam roll helps to press the sleeve seam without creasing the rest of the sleeve.
When a shirt needs a different seam
Not every shirt seam should be flat-felled. On a very sheer shirt, the fold shows through the fabric and the double stitching looks heavy, so a French seam is usually the better choice. On a curved seam, such as a shaped side seam or a curved yoke, folding evenly is harder, and a plain seam with an overlocked or bound finish may be easier to control. On a shirt with a busy print, the topstitching is less visible, which can hide small wobbles, but the fold still needs to be even or the seam will pull. If the pattern allowance is narrow, the fold may not cover the trimmed edge, and the seam should be re-planned with a wider allowance or a different finish. The flat-felled seam is at its best on straight seams in stable shirting fabric, which is where most shirt seams sit.
A shirt made with flat-felled seams is easy to recognise from the inside. The shoulder seams, the side seams and the sleeve seams all show the same folded edge and the same neat topstitching, and there are no loose threads or fraying edges to catch on a jumper worn over the shirt. That consistency is part of what makes a well made shirt feel different from a cheaply made one, even when the fabric is similar. The seams also make the shirt easier to iron, since the flat profile presses smoothly and the fold does not create a ridge under the iron. When a shirt is taken to be altered, a tailor can see at once how the seams were made, and the alteration can follow the same method. Keeping the same finish throughout the shirt is therefore worth the extra time.
For a shirt that will be worn and washed many times, a flat-felled seam at the shoulders, sides and sleeves is a sound choice. Keep the fold even, press well, and topstitch steadily, and the shirt will look finished inside and out.