The Seam Line How seams are made, finished, and fixed

Home / Flat-Felled Seam Allowance

Flat-Felled Seam Allowance

The allowance is the part of a flat-felled seam that most often causes trouble. It needs to be wide enough to fold over and cover the trimmed edge, and the pattern is the place to check it.

Why the allowance is wider

A plain seam only needs enough fabric to hold the stitching and to finish the edge, so its allowance can be narrow. A flat-felled seam needs more, because one allowance is folded over the other and its raw edge is tucked under. If the allowance is too narrow, the fold cannot reach across the trimmed edge, and a strip of raw edge stays exposed. If the allowance is too wide, the fold becomes bulky and may sit unevenly, especially on a light fabric. The width also decides how wide the finished seam looks from the right side, since the fold and the two rows of stitching take up space. That is why the allowance for a flat-felled seam is set at the pattern stage, not improvised at the machine. A pattern drafted for this seam will state the allowance it expects, and that figure should be followed unless there is a clear reason to change it.

Typical allowances and what they mean

Typical allowances for a flat-felled seam are wider than for a plain seam, and they vary with the garment and the fabric. A shirt may use a narrower allowance than a pair of jeans, because the fabric is lighter and the seam is meant to look neat rather than bold. A workwear garment may use a wider allowance, because the fabric is heavier and the seam needs to hold under stress. These are typical ranges, not universal rules, and they are not a substitute for the pattern. The pattern allowance already accounts for the fabric, the garment and the seam position, so it should be treated as the starting point. When a pattern gives no allowance, or when a seam is being added to a garment without a pattern, the allowance should be worked out on scrap fabric first: sew the seam, trim, fold and topstitch, then check that the fold covers the trimmed edge with a little to spare. That test is more reliable than guessing a number.

Trimming one side

Once the first seam is sewn, one allowance is trimmed shorter than the other. The shorter side is the one that sits underneath, and the longer side folds over it. Trimming to about half the width of the longer side is a common approach, but the exact amount depends on the starting allowance and the fabric. The aim is a trimmed edge that is fully covered by the fold, with enough of the longer allowance left to fold under cleanly. Trim evenly along the whole seam, using a seam gauge to check, since a trimmed edge that wanders will show as a fold that is wide in one place and narrow in another. On a thick fabric, trimming more reduces bulk under the fold. On a fabric that frays easily, trimming less leaves a wider safety margin under the fold, though the fold must still cover it. Cut with sharp scissors and keep the cut line smooth, since a jagged trimmed edge can poke out from under the fold.

What goes wrong when the allowance is off

An allowance that is too narrow is the most common problem. The fold reaches only partway across the trimmed edge, and a raw strip remains visible on the wrong side. The fix is to re-sew the seam with a wider allowance, if the fabric allows, or to choose a different seam finish that needs less width. An allowance that is too wide makes the seam bulky and the fold hard to press flat, and the topstitching may wander because the fold is too deep to guide. Trimming the longer side a little more can help, but only if enough width remains to cover the trimmed edge. An uneven allowance, wide in one place and narrow in another, produces a fold that changes width along the seam, which looks untidy and may pull. The remedy is careful cutting and a seam gauge, rather than trying to correct it at the topstitching stage. Pressing cannot fix an allowance that was cut wrong.

Checking the allowance before sewing

Before cutting the garment fabric, read the pattern instructions and check the allowance marked for each seam. Some patterns use the same allowance for every seam, while others vary it by position, so check each seam rather than assuming they are all the same. If the pattern is being traced or copied, transfer the allowance marks as well as the cutting line. When testing on scrap, cut the scrap with the same allowance as the garment, sew the seam in the same way, and measure the finished width. If the fold covers the trimmed edge and the seam lies flat, the allowance is right. If it does not, adjust the allowance on the scrap and test again before touching the garment fabric. That short test saves unpicking a seam that was sewn with the wrong width.

When a pattern is altered, the allowance needs to be checked again. Adding width to a garment, for example, changes the seam line, and the allowance on the new seam line must still be wide enough to fold. If a seam is moved or reshaped, measure the allowance at several points along the new line, since a curved seam can narrow the allowance in places. A pattern that is graded up or down in size should keep the allowance the same, because the allowance is set by the seam type rather than by the garment size, but it is still worth checking after grading. When a seam is sewn without a pattern, for a repair or a simple project, the allowance should be marked on the fabric with chalk or a washable marker before cutting, so it is not left to guesswork at the machine. A marked allowance is easier to sew accurately than an unmarked one.

Check the pattern, test the fold on scrap, and trim evenly. A flat-felled seam with the right allowance folds cleanly, presses flat and topstitches straight, and one with the wrong allowance struggles at every step after it.