Seam Slippage and Stitch Length
Stitch length is the single setting with the most direct effect on seam slippage. A long stitch holds the yarns loosely, a short stitch holds them firmly, and the right length depends on the fabric in front of the needle.
How stitch length affects grip
Each stitch is a loop of thread that passes through the fabric and grips the yarns it crosses. A long stitch spans a wider group of yarns, so each yarn is held less firmly and the thread has more room to slide along the yarns when the seam is pulled. A short stitch spans a narrower group, so each yarn is gripped more closely, and the stitches sit closer together along the seam, which spreads the strain across more points.
The effect is easy to see on a scrap. Sew two seams on the same fabric, one with long stitches and one with short stitches, then pull each scrap firmly across the seam line. The long-stitched seam will usually open a gap beside the stitches with less pull, while the short-stitched seam resists more firmly. The difference is largest on smooth or loosely woven fabrics, where the yarns already slide easily, and smallest on stable, medium-weight cotton, where the weave itself helps hold the stitches.
Why longer stitches make slippage worse
Longer stitches make slippage worse in three ways. First, each stitch holds more yarns, so the grip on any single yarn is weaker. Second, the stitches are further apart, so the strain on the seam is carried by fewer points, and each point carries more load. Third, a long stitch leaves more thread exposed on the surface, which can be pulled or caught, and which gives the yarns more room to move past the thread.
Long stitches are sometimes chosen because they sew faster, or because they look better for topstitching, or because the machine default is set long. On a stable fabric those reasons may be sound. On a slippery fabric such as satin, or an open fabric such as chiffon, they trade a small saving in time for a seam that opens in wear. The stitch length should be chosen for the fabric and the strain the seam will take, not for speed.
Finding the right length
There is no single stitch length that suits every fabric, so the right length has to be found by testing. Start with the length normally used for the fabric weight, sew a test seam on a scrap with the same layers as the garment seam, and pull the scrap firmly across the seam line. If a gap opens beside the stitches, shorten the length by a small step and test again. If the seam holds, check the other side of the balance: look for puckering, for a row of holes that perforate the fabric, or for a seam that feels stiff.
The goal is the longest stitch that still holds the yarns under strain. That length gives a seam that is secure without being over-stitched, and it keeps the fabric from being weakened by too many needle holes. Record the length that worked for that fabric, because the next fabric will probably need a different one. Test again when the fabric, the thread, or the number of layers changes, even if the change looks small.
Short stitches and their limits
Short stitches are not a cure for every slipping seam, and they have limits of their own. Very short stitches place many needle holes close together, which can perforate light fabric and weaken the seam instead of strengthening it. On a fabric that puckers easily, very short stitches can gather the seam line and create a different problem. Short stitches are also harder to remove if the seam needs to be unpicked, and they take longer to sew on a long seam.
When a short stitch alone does not stop slippage, the other factors need to change as well. A wider seam allowance gives the stitches more fabric to grip. A seam finish that encloses the edge, such as a French seam, adds a second line of stitching. A stay tape or interfacing strip along the seam line gives the stitches a stable layer to hold. Stitch length is the first setting to adjust, but it works best as part of a combination, not on its own.
Stitch length across different seams
Not every seam in a garment needs the same stitch length. Seams that take strain in wear, such as side seams, seat seams, and armhole seams, need a shorter stitch that holds firmly. Seams that take little strain, such as a facing edge or a decorative seam, can use a longer stitch without the same risk. Basting stitches, which are meant to be removed, use a long stitch on purpose, because they are temporary and easy to pull out.
Topstitching is a special case. It is visible, so a longer stitch often looks better, but a topstitched seam on slippery fabric can still slip if the underlying seam is not secure. In that case, the structural seam should use a shorter stitch that holds, and the topstitching can use a longer stitch for appearance, because the topstitching is not carrying the strain alone. Thinking about each seam in terms of the strain it will take, rather than using one length for the whole garment, gives seams that hold where they need to hold and look right where they show.