How to Use a Seam Ripper
Using a seam ripper well is mostly about patience. Cut a stitch here and there, pull the thread away, and the seam comes apart cleanly while the fabric stays whole.
Before you start
Set the work down flat and look at the seam first. Check which side the bobbin thread is on, because the stitches are often easier to lift from that side. Look at the fabric too. A tightly woven cotton forgives a small slip, while a loosely woven or delicate fabric does not, so the approach should match the cloth. Good light helps more than a steady hand, since the job is really about seeing each stitch clearly. If the seam is long, decide where to begin. Starting at one end and working steadily along is easier to keep track of than jumping around the middle.
Keep a small brush or a piece of tape nearby for the thread pieces that come out. They cling to fabric and end up everywhere if they are left loose, and a quick brush at the end is easier than picking them out of a finished garment later. A seam ripper with its cap off and a clear work surface is all the equipment the job needs.
The basic method
The method that protects fabric is to cut a stitch every few stitches and then pull the thread out. The blade never travels along the seam, because a blade moving along a seam can catch the fabric itself. Short, separate cuts are slower, but they are the reason the fabric survives.
- Slide the short prong of the fork under a single stitch and lift it slightly away from the fabric.
- Press gently so the cutting edge slices through that one stitch.
- Move three or four stitches along the seam and cut another single stitch.
- Turn the fabric over and pull the thread from the other side, where the cut stitches let the thread come away in a loose line.
- Pick out any short pieces that remain, then brush the seam clean.
The rhythm becomes natural after a few inches: lift, cut, skip, cut, then pull. On a straight seam the work goes quickly. On a seam that was sewn twice, or on topstitching, each row of stitching needs the same treatment in turn, one row at a time.
Removing a long seam
A long seam looks like a large job, but the method does not change. Cut a stitch every few stitches along the whole length first, then pull the thread out in sections. Trying to pull the thread out before enough stitches are cut puts strain on the fabric and can distort it. When the cuts are spaced well, the thread usually pulls away smoothly from the other side.
It helps to work in sections of about fifteen centimetres at a time, cutting and pulling as you go, rather than cutting the entire seam and then pulling. Sections keep the loose fabric under control and make it obvious where the work has reached. If the thread resists, cut a few more stitches in that spot instead of tugging harder. A thread that will not pull is telling you that a stitch is still holding it.
Opening a buttonhole
A seam ripper is also the usual tool for opening a buttonhole after it has been stitched. This is the one time the blade does move along the fabric, but only inside the stitched lines, and with a pin as a guard.
- Place a pin across each end of the buttonhole, just inside the bar tacks, so the blade has a firm stop.
- Put the fork into the middle of the buttonhole, with the cutting edge facing along its length.
- Cut toward one pin, then turn the work around and cut toward the other pin.
- Check that the opening is clean and that the stitching at each end is uncut.
The pins are the safety measure here. If the blade slips, it hits the pin and stops instead of cutting through the end stitching. Cutting from the middle outward, rather than from one end all the way through, gives the same protection on both sides.
When to stop and try something else
Some seams are better taken out another way. Very short stitches, the kind a machine makes when it is set for fine work, can be hard to lift with the fork, and in that case cutting a stitch every two or three stitches and pulling gently still works, it just takes longer. A seam sewn through several thick layers may not let the fork slide under the stitches at all. Forcing it risks a cut in the fabric, so slow down, lift the layers apart slightly, and cut the stitches that are visible. If the fabric is fraying as the stitches come out, stop and check whether the thread is being pulled too hard or the cuts are too close together.
The habit that saves the most fabric is to check the work as it goes. Look at the seam after each section, and look at the fabric for any small nick before moving on. A nick found early can often be worked around when the seam is sewn again. A nick found at the end, after the whole seam is out, is a bigger problem.
Basting stitches come out more easily than ordinary seams, because they are long and loose. Cut one every few inches and pull the thread from the other side, and the whole line usually comes away in a few pulls. It is still worth working in sections rather than pulling a long line at once, since a basting thread that is pulled hard can pucker the fabric it was holding. When the basting has done its job, taking it out carefully leaves the fabric smooth and ready for the next step, with no trace of the temporary stitching.
Once the stitches are out and the seam is clean, the fabric is ready to be sewn again. Press the old seam line lightly before re-sewing, since the crease left by the first seam can pull the new stitching off line if it is ignored.